Characterization of mechanical properties by indentation tests and FE analysis - validation by application to a weld zone of DP590 steel

International Journal of Solids and Structures

Volumn 46, Issue 2, 2009, Pages 344-363

  Chung, Kyung Hwan ^a   Lee, Wonoh ^b   Kim, Ji Hoon ^c   Kim, Chongmin ^d   Park, Sung Ho ^a   Kwon, Dongil ^e   Chung, Kwansoo ^e  

^a POSCO   (South Korea)

^b Korea Institute of Material Science   (South Korea)

^c The Ohio State University   (United States)

^d GENERAL MOTORS CORPORATION   (United States)

^e Seoul National University   (South Korea)

Author keywords

Continuous indentation method; DP steel; Formability; MAG weld zone; Strain rate sensitivity

Indexed keywords

ARSENIC; BENDING TESTS; BIFURCATION (MATHEMATICS); FINITE ELEMENT METHOD; FORMING; GAS WELDING; HEAT AFFECTED ZONE; INDENTATION; MECHANICAL PROPERTIES; STEEL; STRAIN RATE; TENSILE TESTING; WELDING;

ANISOTROPIC YIELD FUNCTIONS; AXIAL TENSIONS; BASE MATERIALS; BIFURCATION THEORIES; CONTINUOUS INDENTATION METHOD; CONTINUOUS INDENTATIONS; DP-STEEL; FAILURE CRITERIONS; FE ANALYSES; FINITE ELEMENTS; FORMING LIMIT DIAGRAMS; INDENTATION TESTS; ISOTROPIC HARDENINGS; K THEORIES; MAG WELD ZONE; MEASURED PROPERTIES; METAL ACTIVE GASSES; NUMERICAL SIMULATIONS; RATE SENSITIVITIES; THREE-POINT BENDING TESTS; WELD ZONES;

WELDS;

EID: 55649116836     PISSN: 00207683     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.ijsolstr.2008.08.041     Document Type: Article

References (51)

1. Abdullah K., Wild P.M., Jeswiet J.J., and Ghasempoor A. Tensile testing for weld deformation properties in similar gage tailor welded blanks using the rule of mixtures. Journal of Materials Processing Technology 112 1 (2001) 91-97
2. Afrin N., Chen D.L., Cao X., and Jahazi M. Microstructure and tensile properties of friction stir welded AZ31B magnesium alloy. Materials Science and Engineering A 472 1-2 (2008) 179-186
3. Ahn J.-H., and Kwon D. Derivation of plastic stress-strain relationship from ball indentations: examination of strain definition and pileup effect. Journal of Materials Research 16 11 (2001) 3170-3178
4. Alcalá J., Giannakopoulos A.E., and Suresh S. Continuous measurements of load-penetration curves with spherical micro-indenters and the estimation of mechanical properties. Journal of Materials Research 13 5 (1998) 1390-1400
5. Antunes J.M., Fernandes J.V., Menezes L.F., and Chaparro B.M. A new approach for reverse analyses in depth-sensing indentation using numerical simulation. Acta Materialia 55 1 (2007) 69-81
6. Aslanlar S., Ogur A., Ozsarac U., Ilhan E., and Demir Z. Effect of welding current on mechanical properties of galvanized chromided steel sheets in electrical resistance spot welding. Materials and Design 28 1 (2007) 2-7
7. Barlat F., and Lian J. Plastic behavior and stretchability of sheet metals. Part. I. A yield function for orthotropic sheets under plane stress conditions. International Journal of Plasticity 5 1 (1989) 51-66
8. Barlat F., Lege D.J., and Brem J.C. A six-component yield function for anisotropic materials. International Journal of Plasticity 7 7 (1991) 693-712
9. Barlat F., Becker R.C., Hayashida Y., Maeda Y., Yanagawa M., Chung K., Brem J.C., Lege D.J., Matsui K., Murtha S.J., and Hattori S. Yielding description of solution strengthened aluminum alloys. International Journal of Plasticity 13 4 (1997) 385-401
10. Barlat F., Brem J.C., Yoon J.W., Chung K., Dick R.E., Choi S.-H., Pourboghrat F., Chu E., and Lege D.J. Plane stress yield function for aluminum alloy sheets-part 1: theory. International Journal of Plasticity 19 9 (2003) 1297-1319
11. Casals O., and Alcalá J. The duality in mechanical property extractions from Vickers and Berkovich instrumented indentation experiments. Acta Materialia 53 13 (2005) 3545-3561
12. Chen, X., Drouin, J., Coopmans, D., Dell'Osso, R., Belanger, P., 2001. Stamping and crush performance of dual phase steel. SAE Technical Paper No. 2001-01-3074, SAE Publication, Warrendale, PA, 2001.
13. Chollacoop N., and Ramamurty U. Experimental assessment of the representative strains in instrumented sharp indentation. Scripta Materialia 53 2 (2005) 247-251
14. Chollacoop N., Dao M., and Suresh S. Depth-sensing instrumented indentation with dual sharp indenters. Acta Materialia 51 13 (2003) 3713-3729
15. Chung K., and Richmond O. A deformation theory of plasticity based on minimum work paths. International Journal of Plasticity 9 8 (1993) 907-920
16. Chung K., Lee M.-G., Kim D., Kim C., Wenner M.L., and Barlat F. Spring-back evaluation of automotive sheets based on isotropic-kinematic hardening laws and non-quadratic anisotropic yield functions. Part I. theory and formulation. International Journal of Plasticity 21 5 (2005) 861-882
17. Dao M., Chollacoop N., Van Vliet K.J., Venkatesh T.A., and Suresh S. Computational modeling of the forward and reverse problems in instrumented sharp indentation. Acta Materialia 49 19 (2001) 3899-3918
18. Doerner M.F., and Nix W.D. A method for interpreting the data from depth-sensing indentation instruments. Journal of Materials Research 1 4 (1986) 601-609
19. Dugdale D.S. Cone indentation experiments. Journal of the Mechanics and Physics of Solids 2 4 (1954) 265-277
20. Fekete, J., Stibich, A., Shi, M., 2001. A comparison of the response of HSLA and dual phase sheet steel in dynamic crush. SAE Technical Paper No. 2001-01-3101, SAE Publication, Warrendale, PA, 2001.
21. Gery D., Long H., and Maropoulos P. Effects of welding speed, energy input and heat source distribution on temperature variations in butt joint welding. Journal of Materials Processing Technology 167 2-3 (2005) 393-401
22. Giannakopoulos A.E., and Suresh S. Indentation of solids with gradients in elastic properties. Part I. Point force. International Journal of Solids and Structure 34 19 (1997) 2357-2392
23. Giannakopoulos A.E., and Suresh S. Indentation of solids with gradients in elastic properties. Part II. Axisymmetric indentors. International Journal of Solids and Structure 34 19 (1997) 2393-2428
24. Giannakopoulos A.E., and Suresh S. Determination of elastoplastic properties by instrumented sharp indentation. Scripta Materialia 40 10 (1999) 1191-1198
25. Hosford W.F. A generalized isotropic yield criterion. Journal of Applied Mechanics 39 2 (1972) 607-609
26. Huh H., Lim J.H., Kim S.B., Han S.S., and Park S.H. Formability of the steel sheet at the intermediate strain rate. Key Engineering Materials (2004) 403-408
27. Jang J., Choi Y., Lee Y.-H., and Kwon D. Instrumented microindentation studies on long-term aged materials: work-hardening exponent and yield ratio as new degradation indicators. Materials Science and Engineering A 395 1-2 (2005) 295-300
28. Jang K.C., Lee D.G., Kuk J.M., and Kim I.S. Welding and environmental test condition effect in weldability and strength of Al alloy. Journal of Materials Processing Technology (2005) 1038-1045
29. Lee M.-G., Kim D., Kim C., Wenner M.L., Wagoner R.H., and Chung K. Spring-back evaluation of automotive sheets based on isotropic-kinematic hardening laws and non-quadratic anisotropic yield functions. Part II. characterization of material properties. International Journal of Plasticity 21 5 (2005) 883-914
30. Liu P., Li Y., Geng H., and Wang J. Microstructure characteristics in TIG welded joint of Mg/Al dissimilar materials. Materials Letters 61 6 (2007) 1288-1291
31. Logan R.W., and Hosford W.F. Upper-bound anisotropic yield locus calculations assuming pencil glide. International Journal of Mechanical Sciences 22 7 (1980) 419-430
32. Marciniak Z., and Kuczynski K. Limits strains in the processes of stretch-forming sheet metal. International Journal of Mechanical Sciences 9 9 (1967) 609-620
33. Marya M., and Gayden X.Q. Development of requirements for resistance spot welding dual-phase (DP600) steels. Part I. The causes of interfacial fracture. Welding Journal 84 (2005) 172-182
34. Millman YU.V., Galanov B.A., and Chugunova S.I. Plasticity characteristic obtained through hardness measurement. Acta Metallurgica et Materialia 41 9 (1993) 2523-2532
35. Nakamachi E., Xie C., and Harimoto M. Drawability assessment of BCC steel sheet by using elastic/crystalline viscoplastic finite element analyses. International Journal of Mechanical Sciences 43 3 (2001) 631-652
36. Oliver W.C., and Pharr G.M. An improved technique for determining hardness and elastic-modulus using load and displacement sensing indentation experiments. Journal of Materials Research 7 6 (1992) 1564-1583
37. Paruz H., and Edmonds D.V. The strain hardening behavior of dual-phase steel. Materials Science and Engineering A 117 (1989) 67-74
38. Qiu X.G., and Chen W.L. The study on numerical simulation of the laser tailor welded blanks stamping. Journal of Materials Processing Technology (2007) 128-131
39. Rodrigues D.M., Menezes L.F., and Loureiro A. The influence of the HAZ softening on the mechanical behaviour of welded joints containing cracks in the weld metal. Engineering Fracture Mechanics 71 13-14 (2004) 2053-2064
40. Rodrigues D.M., Menezes L.F., Loureiro A., and Fernandes J.V. Numerical study of the plastic behaviour in tension of welds in high strength steel. International Journal of Plasticity 20 1 (2004) 1-18
41. Sato Y., Sugiura Y., Shoji Y., Park S.H., Kokawa H., and Ikeda K. Post-weld formability of friction stir welded Al alloy 5052. Materials Science and Engineering A 369 1-2 (2004) 138-143
42. Saunders F.I., and Wagoner R.H. Forming of tailor-welded blanks. Metallurgical and Materials Transactions A 27 9 (1996) 2605-2616
43. Suresh S., Giannakopoulos A.E., and Alcalá J. Spherical indentation of compositionally graded materials: theory and experiments. Acta Materialia 45 4 (1997) 1307-1321
44. Tabor D. The Hardness of Metals (1951), Clarendon Press, Oxford
45. Thaulow C., Paauw A.J., Hauge M., Toyoda M., and Minami F. Fracture property of HAZ-notched weld joint with mechanical mis-matching. Part II. In: Schwalbe K.-H., and Koçak M. (Eds). Mis-Matching of Welds, ESIS 17 (1994), Mechanical Engineering Publications, London 417-432
46. Tirupataiah Y., and Sundararajan G. A dynamic indentation technique for the characterization of the high-strain rate plastic-flow behavior of ductile metals and alloys. Journal of the Mechanics and Physics of Solids 39 2 (1991) 243-271
47. Venkatesh T.A., Van Vliet K.J., Giannakopoulos A.E., and Suresh S. Determination of elasto-plastic properties by instrumented sharp indentation: guidelines for property extraction. Scripta Materialia 42 9 (2000) 833-839
48. Waterschoot T., De A.K., Vandeputte S., and De Cooman B.C. Static strain aging phenomena in cold-rolled dual-phase steels. Metallurgical and Materials Transactions A 34 3 (2003) 781-791
49. Wojnowski D., Oh Y.K., and Indacochea J.E. Metallurgical assessment of the softened HAZ region during multipass welding. Journal of Manufacturing Science and Engineering 122 2 (2000) 310-315
50. Woo W., Choo H., Brown D.W., Liaw P.K., and Feng Z. Texture variation and its influence on the tensile behavior of a friction-stir proceeded magnesium alloy. Scripta Materialia 54 11 (2006) 1859-1864
51. Zeng K., Soderlund E., Giannakopoulos A.E., and Rowcliffe D.J. Controlled indentation: a general approach to determine mechanical properties of brittle materials. Acta Materialia 44 (1996) 1127-1141