Slipline field modeling of orthogonal machining for a worn tool with elastic effects and adhesion friction at the contact regions

Journal of Materials Processing Technology

Volumn 209, Issue 1, 2009, Pages 18-25

  Dundur, S T ^a   Das, N S ^a  

^a NATIONAL INSTITUTE OF TECHNOLOGY   (India)

Author keywords

Adhesion friction; Elastic contact; Flank wear; Orthogonal machining; Slipline field

Indexed keywords

ABS RESINS; ADHESION; LINEAR EQUATIONS; MACHINING; PLASTICS; TOOL STEEL; TRIBOLOGY;

ADHESION FRICTION; ELASTIC CONTACT; FLANK WEAR; ORTHOGONAL MACHINING; SLIPLINE FIELD;

FRICTION;

EID: 53949092762     PISSN: 09240136     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.jmatprotec.2008.01.022     Document Type: Article

References (32)

1. Albrecht A.P. New developments in the theory of metal cutting process Part I-The ploughing process in metal cutting. ASME J. Prod. (November, 1960) 348
2. Bagchi A., and Write P.K. Stress analysis in machining with use of sapphire tools. Proc. R. Soc. Lond. A 409 (1987) 99-113
3. Barrow G., Graham W., Kurimoto T., and Leong Y.F. Determination of rake face stress distribution in orthogonal machining. Int. J. Mach. Tools Des. Res. 22 (1982) 75-85
4. Bhattacharyya A. Metal Cutting Theory and Practice (1984), Central Book Publishers, Calcutta, India
5. Buryta D., Sowerby R., and Yellowley I. Stress distribution on the rake face during orthogonal machining. Int. J. Mach. Tools Manuf. 34 5 (1994) 721-739
6. Chandrasekaran H., and Nagarajan R. Influence of flank wear on the stresses in a cutting tool. ASME J. Eng. Ind. (August, 1977) 566
7. Chandrasekharan H., and Kapoor D.V. Photo-elastic analysis of tool-chip interface stresses. Trans. ASME J. Eng. Ind. 87 (1965) 495-502
8. Childs T.H.C. Elastic effects in metal cutting chip formation. Int. J. Mech. Sci. 22 (1980) 457-466
9. Childs T.H.C., and Mahadi M.I. On the stress distribution between chip and tool during metal cutting. Ann. CIRP 38 1 (1989) 55-58
10. Choudhary S.K., and Kishore K.K. Tool wear measurement in turning using force ratio. Int. J. Mach. Tools Manuf. 40 (2000) 899-909
11. Das N.S., and Dundur S.T. Slipline solutions for metal machining with adhesion friction and elastic effects at the chip-tool contact region. Proc. IMechE, J. Eng. Manuf. Part B 219 (2005)
12. Dewhurst P. The Coulomb friction boundary value problem in plain-strain slipline field theory. First Int. Conf. on Technology of Plasticity (ICTP) Proc. (Advanced Technology of Plasticity). Tokyo, Japan (1984) 1085-1090
13. Dewhurst P. A general matrix operator for linear boundary value problems in slip-line field theory. Int. J. Numer. Methods engineering 21 (1985) 169-182
14. Dewhurst P., and Collins I.F. A matrix methods for constructing slipline field solutions to a class of plain strain plasticity problems. Int. J. Numer. Methods engineering 7 (1973) 357-378
15. Dundur, S.T, 2006. Slipline field analysis of deformation in metal machining with worn tool with adhesion friction in contact regions. Ph.D. Thesis. NIT, Rourkela.
16. Eggleston D.M., Herzog R., and Thompsen E.G. Observations on the angle relationships in metal cutting. Trans. ASME B 81 (1959) 263-279
17. Elanayar S., and Shin Y.C. Modeling of tool forces for warm tool: Flank wear effects. J. Manuf. Sci. Eng. 118 (August) (1996) 359
18. Fang N. Slipline model of machining with round edge tool Part I: new model and theory. Mech. Phys. Solids 51 (2003) 715-742
19. Finnie I., and Shaw M.C. Friction process in metal cutting. Tran. ASME 78 (1956) 1649-1657
20. Hill R. On the limits set by plastic yielding to the intensity of singularities of stress. J. Mech. Phys. Sol. 2 (1954) 278-285
21. Kato S., Yamaguchi K., and Yandra M. Stress distribution at the interface between tool and chip in machining. Trans. ASME J. Eng. Ind. 94 5 (1972) 683-689
22. Kobayashi J.S., and Thomsen E.G. The role of friction in metal cutting. J. Eng. Ind. 82 (1960) 324
23. Kudo H. Some new slip-line solutions for two dimensional steady state. Int. J. Mech. Sci. 7 (1965) 43-55
24. Mackerle J. Finite element analysis and simulation of machining: A bibliograph (1976-1996). J. Mater. Process. Technol. 86 (1999) 17-44
25. Maekawa K., Kitagawa T., and Childs T.H.C. Friction characteristics at chip-tool interface in steel machining. 23rd Leeds Lyon Symposium in Tribology (1997)
26. Manjunathaiah J., and Endes J. A new model and analysis of orthogonal machining with an edge radiused tool. J. Manuf. Sci. Eng. 22 (Aug 2000) 384-390
27. Powell M.J.D. A Fortran subroutine for solving systems of non-linear alzebraic equations. In: Kuester J.L., and Mize J.H. (Eds). Optimization Techniques with FORTRAN (1973), Mc-Graw Hill, New York
28. Shi T., and Ramlingam S. Slip-line solution for orthogonal cutting with a chip breaker and flank wear. Int. J. Mech. Sci. 33 No. 9 (1991) 689-704
29. Trent E.M. Metal cutting and tribology of seizure I-Seizure in metal cutting. Wear 128 (1988) 29-45
30. Wang J., Huang C.Z., and Song W.C. The effect of tool flank wear on the orthogonal cutting process and its practical implications. J. Mater. Process. Technol. 142 (2003) 338-346
31. Woldarf D.J., Dever R.E., and Kapoor S.G. Slip-line field for ploughing during orthogonal cutting. J. Manuf. Sci. Eng. 120-4 (1998) 693-699
32. Yen Y.C., Sohner J., Lilly B., and Alton T. Estimation of tool wear in orthogonal cutting using the finite element analysis. J. Mater. Process. Technol. 146 No. 1 (Feb. 2004) 82-91