2D and 3D numerical models of metal cutting with damage effects

Computer Methods in Applied Mechanics and Engineering

Volumn 193, Issue 39-41 SPEC. ISS., 2004, Pages 4383-4399

  Pantale O ^a   Bacaria, J L ^a   Dalverny, O ^a   Rakotomalala, R ^a   Caperaa, S ^a  

^a UNIVERSITÉ DE TOULOUSE   (France)

Author keywords

ALE; Damage law; Finite elements; Metal cutting; Milling

Indexed keywords

DAMAGE; PLASTIC STRAIN; THERMOMECHANICAL COUPLING;

COMPUTER SIMULATION; FINITE ELEMENT METHOD; LAGRANGE MULTIPLIERS; METAL CUTTING; STRAIN RATE; STRESS ANALYSIS; TEMPERATURE DISTRIBUTION; TORSION TESTING;

NUMERICAL METHODS;

CUTTING;

EID: 4444257790     PISSN: 00457825     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.cma.2003.12.062     Document Type: Article

References (29)

1. Shih A.J.M. Yang H.T.Y. Chandrasekar S. Experimental and finite element simulation of metal cutting process with strain rate and temperature effects Fundam. Issues Machining, ASME PED 43 1990 11-24
2. Sekhon G.S. Chenot J.L. Numerical simulation of continuous chip formation during non steady orthogonal cutting Engrg. Comput. 10 1993 31-48
3. Obikawa T. Sasahara H. Shirakashi T. Usui E. Application of computationl machining method to discontinuous chip formation J. Manuf. Sci. Engrg. 119 1997 667-674
4. Carrol J.T. Strenkowski J.S. Finite element models of orthogonal cutting with application to single point diamond turning Int. J. Mech. Sci. 30 12 1988 899-920
5. Iwata K. Osakada K. Terasaka Y. Process modeling of orthogonal cutting by the rigid-plastic finite element method Trans. ASME 106 1984 132-138
6. Childs T.H.C. Maekawa K. Computer-aided simulation and experimental studies of chip flow and tool wear in the turning of low alloy steels by cemented carbide tools Wear 139 1990 235-250
7. Lin Z.C. Lin S.Y. A coupled finite element model of thermo-elastic-plastic large deformation for orthogonal cutting J. Engrg. Mater. Technol. 114 2 1992 218-226
8. Strenkowski J.S. Carroll J.T. A finite element model of orthogonal metal cutting J. Engrg. Ind. 107 1985 349-354
9. Lin Z.C. Pan W.C. A thermoelastic-plastic large deformation model for orthogonal cutting with tool flank wear, i: Computational procedures Int. J. Mech. Sci. 35 10 1993 829-840
10. Marusich T.D. Ortiz M. Modelling and simulation of high-speed machining Int. J. Numer. Meth. Engrg. 38 1995 3675-3694
11. Lin Z.C. Lin S.Y. Fundamental modeling for oblique cutting by thermoelastic plastic fem Int. J. Mech. Sci. 1999 941-965
12. Maekawa K. Nagayama T. Ohshima I. Murata R. Finite element simulation of oblique cutting Bull. Jpn. Soc. Precision Engrg. 24 3 1990 221-222
13. Ueda K. Manabe K. Rigid-plastic fem analysis of three-dimensional deformation field in chip formation process Ann. CIRP 42 1993 35-38
14. O. Pantalé, Modélisation et Simulation Tridimensionnelles de la Coupe des Métaux, Ph.D. thesis, Université de Bordeaux I, School, 1996
15. Rakotomalala R. Joyot P. Touratier M. Arbitrary Lagrangian-Eulerian thermomechanical finite element model of material cutting Commun. Numer. Meth. Engrg. 9 1993 975-987
16. P. Joyot, R. Rakotomalala, M. Touratier, Modelisation de 1'usinage formulée en euler-lagrange arbitraire. Supplément au journal de physique III, 3 (1993) 1141-1144
17. Olovsson L. Nilsson L. Simonsson K. An ale formulation for the solution of two-dimensional metal cutting problems Comput. Struct. 72 1999 497-507
18. O. Pantalé, R. Rakotomalala, M. Touratier, An ale three-dimensional model of orthogonal and oblique metal cutting processes, Int. J. Forming Processes l (3) (1998) 371-388.
19. Hughes T.J.R. The Finite Element Method; Linear Static and Dynamic Finite Element Analysis 1987 Prentice Hall
20. Brooks A.N. Hughes T.J.R. Streamline upwind/Petrov-Galerkin formulations for convective dominated flows with particular emphasis on the incompressible Navier-Stokes equations Comput. Meth. Appl. Mech. Engrg. 32 1982 199-259
21. Van Leer B. Towards the ultimate conservative difference scheme iv. A new approach to numerical convection J. Comput. Phys. 23 1977 276-299
22. Benson D.J. Momentum advection on staggered mesh J. Comput. Phys. 100 1 1992 143-162
23. R. Johnson, W.K. Cook, A constitutive model and data for metals subjected to large strains high strain rates and high temperatures, 7th International Symposium on Balistics; The Hague, 1983, pp. 541-547
24. Abaqus. Reference Manual. Hibbitt, Karlsson and Sorensen Inc., 100 Medway Street, Providence, Rl, 02906-4402, USA, 1989
25. I. Nistor, O. Pantalé, S. Caperaa, C. Sattouf, Identification of a dynamic viscoplastic flow law using a combined Levenberg-Marquardt and Monte-Carlo algorithm, In CIMNE, editor, VII International Conference on Computational Plasticity, COMPLAS 2003, Barcelona, 4, 2003
26. Johnson G.R. Cook W.H. Fracture characteristics of three metals subjected to various strains, strain rates, temperatures and pressures Engrg. Fracture Mech. 21 l 1985 31-48
27. Hancock J.W. Mackenzie A.C. On the mechanisms of ductile failure in high-strength steels subjected to multi-axial stress-states J. Mech. Phys. Solids 24 1976 147-169
28. J. Tyson, T. Schmidt, K. Galanulis, Advanced photogrammetry for robust deformation and strain measurement, In: Proc. of the 2002 SEM Annual Conference and Exhibition of Experimental and Applied Mechanics, 2002
29. Shih A.J.M. Yang H.T.Y. Experimental and finite element predictions of residual stresses due to orthogonal metal cutting Int. J. Numer. Meth. Engrg. 36 1993 1487-1507