Bending of tube and section made of strain-hardening materials

Journal of Materials Processing Technology

Volumn 203, Issue 1-3, 2008, Pages 372-380

  El Megharbel, A ^a   El Nasser, G A ^a   El Domiaty, Aly ^a  

^a Port Said University   (Egypt)

Author keywords

Residual stresses; Springback; Tube bending

Indexed keywords

BENDING STRENGTH; CONSTITUTIVE EQUATIONS; PLASTIC PRODUCTS; RESIDUAL STRESSES; STRAIN HARDENING;

PLASTIC MATERIALS; SPRINGBACK; STRAIN-HARDENING MATERIALS; TUBE BENDING;

ELASTOPLASTICITY;

EID: 43849100611     PISSN: 09240136     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.jmatprotec.2007.10.078     Document Type: Article

References (18)

1. Al-Qureshi H.A. Elastic-plastic analysis of tube bending. Int. J. Mach. Tools Manuf. 39 (1999) 87-104
2. Corona E. A simple analysis for bend-stretch forming of aluminum extrusions. Int. J. Mech. Sci. 46 (2004) 433-448
3. El Megharbel, A., 1992. Springback property after forming by bending with tension. Master's Thesis. Suez Canal University.
4. El Megharbel A., El-Domiaty A., and Shaker M. Springback and residual stresses after stretch bending of workhardening sheet metal. J. Mater. Process. Technol. 24 (1990) 191-200
5. El-Domiaty A.A., Shabara M.A.N., and Al-Ansary M.D. Determination of stretch-bendability of sheet-metals. Int. J. Mach. Tools 36 5 (1996) 635-650
6. Fei D., and Hodgson P. Experimental and numerical studies of springback in air v-bending process for cold rolled TRIP steels. Nucl. Eng. Des. 236 (2006) 1847-1851
7. Goodarzi M., Kuboki T., and Murata M. Deformation analysis for the shear bending process of circular tubes. J. Mater. Process. Technol. 162/163 (2005) 492-497
8. Heng L.I., Yang H., Zhan M., and Gu R.-J. Forming characteristics of thin-walled tube bending process with small bending radius. Trans. Nonferr. Met. Soc. China 16 (2006) s613-s623
9. Jeunechamps P.-P., Ho K.C., Lin J., Ponthot J.-P., and Dean T.A. A closed form technique to predict springback in creep age-forming. Int. J. Mech. Sci. 48 (2006) 621-629
10. Özgür T., Ulvi S., and Ahmet O. Determination springback amount of steel sheet metal has 0.5 mm thickness in bending dies. Mater. Des. 27 (2006) 251-258
11. Quach W.M., Teng J.G., and Chung K.F. Residual stresses in steel sheets due to coiling and uncoiling: a closed-form analytical solution. Eng. Struct. 26 (2004) 1249-1259
12. Souichiro N., Kunio O., and Keisuke N. Proposal for reducing press working load and highly accurate evaluation of springback error in bending automobile sheet metal. JSAE Rev. 24 (2003) 283-288
13. Tang N.C. Plastic-deformation analysis in tube bending. Int. J. Pres. Vessels Piping 77 (2000) 751-759
14. Volkan E., Haluk D., and Mustafa I.G. Finite element analysis of springback in bending of aluminum sheets. Mater. Des. 23 (2002) 223-229
15. Yang H., and Lin Y. Wrinkling analysis for forming limit of tube bending processes. J. Mater. Process. Technol. 152 (2004) 363-369
16. Zhan M., Yang H., and Huang L. A numerical-analytic method for quickly predicting springback of numerical control bending of thin-walled tube. J. Mater. Sci. Technol. 22 5 (2006)
17. Zhan M., Yang H., Huang L., and Gu R. Springback analysis of numerical control bending of thin-walled tube using numerical-analytic method. J. Mater. Process. Technol. 177 (2006) 197-201
18. Zhang Z.T., and Hu S.J. Stress and residual stress distributions in plane strain bending. Int. J. Mech. Sci. 40 6 (1998) 533-543