Tensile and wear behaviour of in situ Al-7Si/TiB2 particulate composites

Wear

Volumn 265, Issue 1-2, 2008, Pages 134-142

  Kumar, S ^a   Chakraborty, M ^b   Subramanya Sarma, V ^a   Murty, B S ^a  

^a INDIAN INSTITUTE OF TECHNOLOGY MADRAS   (India)

^b INDIAN INSTITUTE OF TECHNOLOGY   (India)

Author keywords

Al 7Si alloy; Dry sliding wear; In situ composites; TiB2

Indexed keywords

ALUMINUM ALLOYS; SYNTHESIS (CHEMICAL); TENSILE STRENGTH; WEAR OF MATERIALS;

AL-7SI ALLOY; DRY SLIDING WEAR; IN SITU COMPOSITES;

COMPOSITE MATERIALS;

ALUMINUM ALLOYS; COMPOSITE MATERIALS; SYNTHESIS (CHEMICAL); TENSILE STRENGTH; WEAR OF MATERIALS;

EID: 41149152385     PISSN: 00431648     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.wear.2007.09.007     Document Type: Article

References (29)

1. Thanh L.N., and Suery M. Influence of oxide coating on chemical stability of SiC particles in liquid aluminum. Scripta Metall. Mater. 25 (1991) 2781-2786
2. Rajan T.P.D., Pillai R.M., and Pai B.C. Reinforcement coatings and interfaces in aluminium metal matrix composites. J. Mater. Sci. 33 (1998) 3491-3503
3. Murty B.S., Thakur S.K., and Dhindaw B.K. On the infiltration behavior of Al, Al-Li and Mg melts through SiCp bed. Metall. Mater. Trans. 31A (2000) 319-325
4. Tham L.M., Gupta M., and Cheng L. Effect of limited matrix-reinforcement interfacial reaction on enhancing the mechanical properties of aluminium-silicon carbide composites. Acta Mater. 49 (2001) 3243-3253
5. Tjong S.C., and Ma Z.Y. Microstructural and mechanical characteristics of in situ metal matrix composites. Mater. Sci. Eng. R29 (2000) 49-113
6. Aikin Jr. R.M. The mechanical properties of in-situ composites. JOM 49 8 (1997) 35-39
7. 2 composite. Wear 240 (2000) 59-64
8. Tyagi R. Synthesis and tribological characterization of in-situ cast Al-TiC composites. Wear 259 (2005) 569-576
9. 3Ti particles. Metall. Mater. Trans. 30A (1999) 243-247
10. 2 alloys. Mater. Sci. Technol. 9 (1993) 833-840
11. 2 particle reinforcement on the creep resistance of hypoeutectic Al-12Si alloy. J. Alloys Comp. 389 (2005) 275-280
12. Schaffer P.L., Arnberg L., and Dahle A.K. Segregation of particles and its influence on the morphology of the eutectic silicon phase in Al-7 wt.% Si alloys. Scripta Mater. 54 (2006) 677-682
13. 2 particles. Scripta Mater. 54 (2006) 1093-1097
14. 2 particles on aging response of Al-4Cu alloy. Mater. Sci. Eng. A386 (2004) 296-300
15. 2 particles on sliding wear behavior of Al-4Cu alloy. Wear 262 (2007) 160-166
16. Kumar S., Subramanya Sarma V., and Murty B.S. Influence of in-situ formed TiB2 particles on the abrasive wear behaviour of Al-4Cu alloy. Mater. Sci. Eng. A 465 (2007) 160-164
17. 2 metal matrix composites. J. Metall. Mater. Sci. 43 (2002) 93-101
18. Murty B.S., Kori S.A., and Chakraborty M. Grain refinement of aluminium and its alloys by heterogeneous nucleation and alloying. Int. Mater. Rev. 18 (2002) 2-29
19. Prasada Rao A.K., Murty B.S., and Chakaraborty M. Improvement in tensile strength and load bearing capacity during dry wear of Al-7Si alloy by combined grain refinement and modification. Mater. Sci. Eng. A395 (2005) 323-326
20. Stephens J.J., Lucas J.P., and Hosking F.M. Cast Al-7Si composites: effect of particle type and size on mechanical properties. Scripta Mater. 22 (1988) 1307-1312
21. p and Mg/Al metal matrix on wear, coefficient of friction and microhardness. Wear 247 (2001) 191-201
22. Min Z., Gaohui W., Longtao J., and Zuoyong D. Friction and wear properties of TiB2p/Al composite. Comp. Part A: App. Sci. Manu. 37 (2006) 1916-1921
23. Clarke J., and Sarkar A.D. Wear characteristics of as-cast binary aluminium-silicon alloys. Wear 54 (1979) 7-16
24. Prasada Rao A.K., Das K., Murty B.S., and Chakaraborty M. Effect of grain refinement on wear properties of Al and Al-7Si alloy. Wear 257 (2004) 148-153
25. Archard J.F. Contact and rubbing of flat surface. J. Appl. Phys. 24 (1953) 981-988
26. Venkataraman B., and Sundararajan G. The sliding wear behaviour of Al-SiC particulate composites-II. The characterization of subsurface deformation and correlation with wear surface. Acta Mater. 44 (1996) 461-473
27. Godet M. The third body approach: a mechanical view of wear. Wear 100 (1984) 437-452
28. Alpas A.T., and Zhang J. Effect of microstructure (particulate size and volume fraction) and counterface material on the sliding wear resistance of particulate-reinforcement aluminum matrix composites. Metall. Mater. Trans. 25A (1994) 969-983
29. p composites. I. Frictional and wear-rate characteristics. Comp. Sci. Technol. 59 (1999) 55-63