Influence factors on wear resistance of two alumina matrix composites

Wear

Volumn 265, Issue 1-2, 2008, Pages 27-33

  Zhang, F C ^a   Luo, H H ^b   Wang, T S ^a   Roberts, S G ^c   Todd, R I ^c  

^a YANSHAN UNIVERSITY   (China)

^b INSTITUTE OF SEMICONDUCTORS   (China)

^c UNIVERSITY OF OXFORD   (United Kingdom)

Author keywords

Alumina; Ceramic composites; Fracture mode; Wear resistance

Indexed keywords

ALUMINA; METALLIC MATRIX COMPOSITES; SILICON CARBIDE; SURFACE ANALYSIS;

CERAMIC COMPOSITES; FRACTURE MODE;

WEAR RESISTANCE;

ALUMINA; METALLIC MATRIX COMPOSITES; SILICON CARBIDE; SURFACE ANALYSIS; WEAR RESISTANCE;

EID: 41149120658     PISSN: 00431648     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.wear.2007.08.011     Document Type: Article

References (23)

1. RainforthTitle W.M. The wear behaviour of oxide ceramics-a review. J. Mater. Sci. 39 (2004) 6705-6721
2. Magnani G., and Brillante A. Effect of the composition and sintering process on mechanical properties and residual stresses in zirconia-alumina composites. J. Eur. Ceram. Soc. 25 (2005) 3383-3392
3. Sun Y., Li B., and Yang D.Q. Unlubricated friction and wear behavior of zirconia ceramics. Wear 215 (1998) 232-236
4. Sternitzke M., Dupas E., Twigg P.C., and Derby B. Surface mechanical properties of alumina matrix nanocomposites. Acta Mater. 45 (1997) 3963-3973
5. Taktak S., and Baspinar M.S. Wear and friction behaviour of aluminia/mullite composite by sol-gel infiltration technique. Mater. Design 26 (2005) 459-464
6. 3/SiC composites. J. Eur. Ceram. Soc. 26 (2006) 1273-1279
7. 3 nanocomposites. Wear 259 (2005) 553-561
8. Evans A.G. In: Hockey B.J., and Rice R.W. (Eds). The Science of Ceramic Machining and Surface Finishing, II (1979), US Govt. Printing Office 1-14
9. 3-SiC submicro- and nano-composites. J. Am. Ceram. Soc. 88 (2005) 179-183
10. Merino J.L.O., and Todd R.I. Relationship between wear rate, surface pullout and microstructure during abrasive wear of alumina and alumina/SiC nanocomposites. Acta Mater. 53 (2005) 3345-3357
11. 3-SiC ceramic nanocomposites. Scripta Mater. 42 (2000) 555-560
12. Merino J.L.O., Cock A., Robert S.G., and Todd R.I. Quantitative surface fractography of alumina and alumina-SiC composites during diamond grinding. Key Eng. Mater. 250 (2005) 149-159
13. 3/mullite composite. J. Mater. Sci. 42 (2007) 6798-6802
14. Levin I., Kaplan W.D., Brandon D.G., and Wieder T. Residual-stresses in alumina-SiC nanocomposites. Acta Mater. 42 (1994) 1147-1154
15. Anstis G.R., Chantikul P., Lawn B.R., and Marshall D.B. A critical evaluation of indentation techniques for measuring fracture toughness. I. Direct crack measurements. J. Am. Ceram. Soc. 64 (1981) 533-538
16. Rohan P., Neufuss K., Dubský J., Prchlík L., and Holzgartner C. Thermal and mechanical properties of cordierite, mullite and steatite produced by plasma spraying. Ceram. Int. 30 (2004) 597-603
17. 3 particle size on the mechanical properties of alumina-based ceramics. Mater. Sci. Eng. A 452-453 (2007) 545-551
18. Root J.H., Sullivan J.D., and Marple B.R. Residual stress in Alumina-mullite composites. J. Am. Ceram. Soc. 74 (1991) 579-583
19. 3+ fluorescence microscopy. J. Eur. Ceram. Soc. 23 (2003) 1779-1783
20. 3-SiC nanocomposites. J. Am. Ceram. Soc. 88 (2005) 1536-1543
21. Selsing J. Internal stress in ceramics. J. Am. Ceram. Soc. 44 (1961) 419-492
22. Todd R.I., and Derby B. Thermal stress-induced microcracking in alumina-20% SiCp composites. Acta Mater. 52 (2004) 1621-1629
23. Kim B.N., Wakayama S., and Kawahara M. Characterization of 2-dimensional crack propagation behavior by simulation and analysis. Int. J. Fract. 75 (1996) 247-259