Fast modeling of phase changes in a particle injected within a d.c plasma jet

Journal of Thermal Spray Technology

Volumn 16, Issue 5-6, 2007, Pages 744-750

  Ettouil, F Ben ^a   Pateyron, B ^a   Ageorges, H ^a   El Ganaoui, M ^a   Fauchais, P ^a   Mazhorova, O ^b  

^a UNIVERSITY OF LIMOGES   (France)

^b KELDYSH INSTITUTE OF APPLIED MATHEMATICS   (Russian Federation)

Author keywords

d.c. plasma spray; Fast modeling; Nanostructured materials; Phase change

Indexed keywords

ADAPTIVE GRID; DIRECT-CURRENT (D.C) PLASMA SPRAY;

CALCULATIONS; EVAPORATION; HEAT TRANSFER; MATHEMATICAL MODELS; MELTING; NANOSTRUCTURED MATERIALS; PHASE CHANGE MATERIALS; PLASMA JETS; SOLIDIFICATION; THERMAL CONDUCTIVITY; ZIRCONIA;

PLASMA SPRAYING;

EID: 37249043689     PISSN: 10599630     EISSN: None     Source Type: Journal    
DOI: 10.1007/s11666-007-9075-y     Document Type: Conference Paper

References (13)

1. H.P. Li, E. Pfender, X. Chen, Application of Steenbeck's Minimum Principle for Three-dimensional Modeling of DC Arc Plasma Torches, J. Phys. D: Appl. Phys. 36, 1084-1096 (2003)
2. P. Freton, J.J. Gonzalez, A. Gleizes, Comparison Between a Two- and Three-Dimensional Arc Plasma Configuration, J. Phys. D: Appl. Phys. 33, 2442-2452 (2000)
3. C. Baudry, Contribution to the Transient and 3D Modeling of the Dynamic Behavior of the Arc within a Plasma Spray Torch, Ph.D. thesis, Univ. of Limoges, 2003
4. V. Alexiades, D. Solomon, Mathematical Modeling of Melting and Freezing Process (Hemisphere Publishing Corporation, USA, 1993)
5. M. Bouneder, Modélisation des Transfert de Chaleur et de Masse dans les Poudres Composites Métal/Céramique en Projection Thermique, Ph.D. Thesis, Limoges University, 2006 (in French)
6. B. Pateyron et al., Jets & Powders Software (www.unilim.fr/spcts/), 2007
7. G. Delluc, H. Ageorges, B. Pateyron, P. Fauchais, Fast Modeling of Plasma Jet and Particle Behaviors in spray conditions, High Temp. Mat. Process. 9, 211-226 (2005)
8. E. Pfender, Particle Behaviour in Thermal Plasma, Plasma Chem. Plasma Proc. 9(1), 167S-194S (1989)
9. Y.C. Lee, C. Hsu, and E. Pfender, Modelling of Particle Injection into a D.C Plasma Jet, 5th International Symposium on Plasma Chemistry, Edinburgh, Scotland, Vol. 2, 1981, p 795-801
10. X. Chen, Heat and Momentum Transfer Between Thermal Plasma and Suspended Particles for Different Knudsen Numbers. Thin Solid Films 345, 140-145 (1999)
11. E. Bourdin, P. Fauchais, M. Boulos, Transient Heat Conduction Under Plasma Condition. Int. J. Heat Mass Transfer. 26(4), 582-652 (1983)
12. C.J. Knight, Theoretical Modeling of Rapid Surface Vaporization with Back Pressure, AIAA J. 17(5), 519-523 (1979)
13. R.S. Lima, A. Kucuk and C. Berndt, Bimodal Distribution of Mechanical Properties on Plasma Sprayed Nanostructured Partially Stabilized Zirconia. Mat. Sci. Eng. A327, 224-232 (2002)