A comprehensive characterization of 3D surface topography induced by hard turning versus grinding

Journal of Materials Processing Technology

Volumn 197, Issue 1-3, 2008, Pages 189-199

  Waikar, R A ^a   Guo, Y B ^a  

^a University of Alabama   (United States)

Author keywords

Machining; Surface integrity; Surface topography

Indexed keywords

BEARING CAPACITY; TURNING;

FLUID RETAINABILITY; PRECISION MACHINING; SURFACE INTEGRITY;

SURFACE TOPOGRAPHY;

EID: 37049036139     PISSN: 09240136     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.jmatprotec.2007.05.054     Document Type: Article

References (29)

1. Berthe D., Michau B., Flamand L., and Godet M. Effect of roughness ratio and hertz pressure on micropits and spalls in concentrated contacts: theory and experiments. Proceedings of the Fourth Leeds-Lyon Symposium (1977) 233-242
2. Borbe, C., Bauteilverhalten hartgedrehter oberflachen, German Ph.D. Thesis, University Hannover, 2001.
3. Brinksmeier E., and Giwerzew A. Chip formation mechanisms in grinding at low speeds. Ann. CIRP 52 1 (2003) 253-258
4. Denkena B., Tonshoff H.K., Friemuth T., Muller C., Zenner H., Renner F., and Koehler M. Fatigue strength of hard turned components. Proceedings of the First International Conference on Manufacturing Engineering. Sani-Haldiki (2002)
5. Dong W.P., Sullivan P.J., and Stout K.J. Comprehensive study of parameters for characterizing three dimensional surface topography. III. Parameters for characterizing amplitude and some functional properties. Wear 178 (1994) 29-43
6. Dong W.P., Sullivan P.J., and Stout K.J. Comprehensive study of parameters for characterizing three dimensional surface topography. IV. Parameters for characterizing spatial and hybrid properties. Wear 178 (1994) 45-60
7. Elbestawi M.A., Koshy P., and Iwasaki A. Surface generation with engineered diamond grinding wheels: insight from simulation. Ann. CIRP 52 1 (2003) 271-274
8. Guo Y.B., and Janowski G.M. Microstructural characterization of white layers by hard turning and grinding. Trans. NAMRI/SME 32 (2004) 367-374
9. Guo Y.B., and Sahni J. A comparative study of the white layer by hard turning versus grinding. Int. J. Mach. Tools Manuf. 44 (2004) 135-145
10. Guo Y.B., and Schwach D.W. An experimental investigation of white layer on rolling contact fatigue using acoustic emission technique. Int. J. Fatigue 27 (2005) 1051-1061
11. Guo Y.B., and Warren A.W. Microscale mechanical behavior of the subsurface by finishing processes. ASME J. Manuf. Sci. Eng. 127 (2004) 333-338
12. Jahanmir S., and Suh N.P. Surface topography and integrity effects on sliding wear. Wear 44 (1977) 87-99
13. Kelley B.W., and Lemanski A.J. Lubrication of involute gearing. Proc. Inst. Mech. Eng. 182 3 (1967) 173-184
14. Klocke F., Brinksmeier E., and Weinert K. Capability profile of hard cutting and grinding processes. Ann. CIRP 54 2 (2005) 557-581
15. Kundrak J., and Bana V. Microgeometry of bore holes after hard machining. Seventh International Research Conf. "Trends in the Development of Machinery and Associated Technology". Lloret de Mar, Barcelona, Spain, 15-16 September (2003)
16. Malkin S. Grinding Technology: Theory and Application of Machining with Abrasive (1989), Ellis Horwood, Chichester and John Wiley, New York, United States of America
17. Marinescu I.D., Rowe W.B., Dimitrov B., and Inasaki I. Tribology of Abrasive Machining Processes (2004), William Andrew, New York, United States of America
18. Pawlus P. Change of topography in initial state of engine life. Wear 209 (1997) 69-83
19. Renner, F., Zenner, H., Borbe, C., Muller, C., Tonshoff, H.K., Hartdrehen oder schleifen bei einsatzgeharteten bauteilen? Kosten, flexibilitat und bertiebsfestigkeit, DVM-Bericht 128 Fertigungsverfahren und Betriebdfestigkeit, Schaffhausen, 2001.
20. Schwach D.W., and Guo Y.B. A fundamental study on the impact of surface integrity by hard turning on rolling contact fatigue. Trans. NAMRI/SME 33 (2005) 541-548
21. Schwach D.W., and Guo Y.B. Feasibility of producing optimal surface integrity by process design in hard turning. Mater. Sci. Eng. A 395 (2005) 116-123
22. Seker U., Ciftci I., and Hasirci H. The effect of alloying elements on surface roughness and cutting forces during machining of ductile iron. Mater. Des. 24 1 (2003) 47-51
23. Siebel E., and Gaier M. Untersuchungen uber den einfluss der oberflachenbeschaffenheit auf die dauerschwingfestigkeit metallischer bauteile. VDI-Z Integrierte Produktion 98 30 (1956) 1715-1723
24. Singh R., and Melkote S.N. Frictional response of precision finished surfaces in pure sliding. Wear 258 (2005) 1500-1509
25. Suh N.P., and Nagao T. Implications of wear theories on surface quality and functional requirements. Ann. CIRP 25 2 (1976) 513-519
26. Valasek I. Tribological Handbook (1996), Tribotechnik Kft, Budapest
27. Warren A.W., and Guo Y.B. On the clarification of surface hardening mechanisms by hard turning and grinding. Trans. NAMRI/SME 34 (2006) 309-316
28. Whitehouse D.J. The parameter rash-is there a cure?. Wear 83 (1982) 75-78
29. Zhou R.S., and Hashimoto F. A new rolling contact surface and "no run in" performance bearings. Proceedings of the ASME/STLE Tribology Conference. Maui Hawaii (1994) (Paper no. 94-Trib-28)