Study of the brazeability of aluminum matrix composites

Welding Journal (Miami, Fla)

Volumn 76, Issue 12, 1997, Pages 92-s

  Urena A ^a   Gomez De Salazar J M ^a   Escalera, M D ^a   Fernandez M I ^a  

^a UNIVERSIDAD COMPLUTENSE DE MADRID   (Spain)

Author keywords

6061 Aluminum; 7005 Aluminum; BalSi4 Filler Metal; Brazeability; Drop Test; Metal Matrix Composites; Postbrazing Heat; Shear Strength; Treatment

Indexed keywords

EID: 3643061439     PISSN: 00432296     EISSN: None     Source Type: Journal    
DOI: None     Document Type: Article

References (19)

1. Ellis, M. B. D., Gittos, M. F., and Threadgill, P. L. 1994. Joining of Aluminum Based Metal Matrix Composites: Initial Studies. TWI Report. N.501 Abington Hall.
2. p Reinforced Aluminum A-356 Metal Matrix Composite. Scripta Metallurgia and Materialia 28, pp. 1341-1346.
3. Ryabov, V. R., and Pavlenko, Yu. V. 1991. Welding Composite Materials: Review. Paton Welding Journal. 3 pp. 211-219.
4. Lane, C. T. Welding of Metal Matrix Composites. 1994. AWS Welding Handbook. Vol. 3. American Welding Society.
5. Holcomb, S. 1991. Effect of Spinel Formation on Mechanical Properties of Alumina Reinforced Aluminum Composites. Conf. Proc. Advanced in Production and Fabrication of Light Metals and Matrix Composites. Can. Inst. Min. Metal & Petrol., Montreal, Ed. M. M. Avedesian, pp. 643-649.
6. Clyne, T. W., and Withers P. J. 1993. An Introduction to Metal Matrix Composites. Cambridge Solid State Science Series, Cambridge University Press, p. 359.
7. Sugiyama, Y. 1989. Brazing of Aluminum Alloys. Welding International Journal 8, pp. 700-710.
8. Keller, D. L., McDonald, M. M., Heilple, C. R,. Johns, W. L., and Hofmann, W. E. 1990. Wettability of Brazing Filler Metals. Welding Journal 69, pp. 31-34.
9. Humpston, G., and Jacobson, D. M. 1993. Principles of Soldering and Brazing, ASM International, Materials Park, Ohio, p. 188.
10. Brandi, S. D., Liu, S., Indacochea, J. E., and Xu, R. 1993. Brazeability and Solderability of Engineering Materials. Metal Handbook.Vol. 6: Welding, Brazing and Soldering. Ed. J. R. Davies, et al. ASM International, Materials Park, Ohio, pp. 617-637.
11. Massalski, T. B. 1986. Binary Phase Diagrams. American Society for Metals, Metals Park, Ohio, Vol. 1, p. 165.
12. Schwartz, M. 1991. Brazing: For the Engineering Technologists, Chapman & Hall, London, England, pp. 9-10.
13. Cawley, J. D. 1991. Introduction to Ceramic-Metal Joining. Conf. Proc. Metal-Ceramic Joining. Eds. P. Kumar, and V. A. Geenhut, The Min. Met. & Mat. Soc., pp. 3-11.
14. Nicholas, M. G. 1989. Metal-Ceramic Interfaces. Surfaces and Interfaces of Ceramic Materials. Ed. L. C. Dufourd, et al. Klumwer Academic Publisher, Norwell, MA, pp. 394-417.
15. Klomp, J. T. 1989. Thermodynamics and Chemistry of Ceramic-Metal Interfaces. Surfaces and Interfaces of Ceramic Materials. Edited L. C. Dufourd, et al. Klumwer Academic Publisher, Norwell, MA, pp. 375-392.
16. Schmatz, D. J. 1983. Grain Boundary Penetration During Brazing of Aluminum. Welding Journal 62, pp. 267-s to 271-s.
17. Dunford, D. V., and Partridge, P. G. 1990. Strength and fracture behaviour of diffusion-bonded joints in Al-Li (8090) alloy. Part 1: Shear strength. Journal of Materials Science 25, pp. 4957-4964.
18. DURALCAN USA. 1993. Duralcan Composites for Wrought Products: Properties Data (SI units). San Diego, California.
19. Skibo, M. D. 1993. Alumina Particulate Reinforced 7000 Series Composites. SAE Technical Paper Series, N930181, SAE International, Warrendale.