Orientational design of anisotropic materials using the hill and Tsai-Wu strength criteria

Mechanics of Composite Materials

Volumn 39, Issue 6, 2003, Pages 509-520

  Majak, J ^a   Hannus, S ^a  

^a UNIVERSITY OF TARTU   (Estonia)

Author keywords

Hill and Tsai Wu strength criteria; Optimum orientation

Indexed keywords

ANISOTROPY; ELASTICITY; ELASTOPLASTICITY; FAILURE ANALYSIS; STRAIN; STRENGTH OF MATERIALS; STRESS ANALYSIS;

HILL AND TSAI-WU STRENGTH CRITERIA; OPTIMUM ORIENTATION; ORTHOTROPIC MATERIALS;

MATERIALS SCIENCE;

EID: 3543116606     PISSN: 01915665     EISSN: None     Source Type: Journal    
DOI: 10.1023/B:MOCM.0000010623.38596.3e     Document Type: Article

References (20)

1. P. Pedersen, "On optimal orientation of orthotropic materials," Struct. Optim., 1, No. 2, 101-106 (1989).
2. P. Pedersen, "Some general optimal design results using anisotropic, power-law nonlinear elasticity," Struct. Optim., 15, 73-80 (1998).
3. K. A. Lurie, A. V. Cherkaev, and A. V. Fedorov, "Regulation of optimal design problems for bars and plates," JOTA, 37, No. 4, 499-522 (1982).
4. J. Majak, "Orientational design of nonorthotropic two-dimensional materials," Mech. Compos. Mater., 37, No. 1, 27-38 (2001).
5. J. Lellep and J. Majak, "Optimal material orientation of nonlinear elastic orthotropic materials," Struct. Optim., 14, No. 2/3, 116-120 (1997).
6. Z. Hashin, "Failure criteria for unidirectional fiber composites," J. Appl. Mech., 47, 329 (1980).
7. Y. P. Arramon, M. M. Meharabadi, D. W. Martin, and S. C. Cowin, "A multidimensional anisotropic strength criterion based on Kelvin modes," Int. J. Solids Struct., 37, 2915-2935 (2000).
8. R. M. Christensen, "Stress-based yield/failure criteria for fiber composites," Int. J. Solids Struct., 34, 529-543 (2000).
9. K.-S. Liu and S. W. Tsai, "A progressive quadratic failure criterion for a laminate," Compos. Sci. Technol., 50, 1026-1032 (1998)
10. W. Paepegem and J. Degrieck, "Calculation of damage-dependent directional failure indices from the Tsai-Wu static failure criterion," Compos. Sci. Technol., 63, 305-310 (2003).
11. R. C. Tennyson, D. McDonald, and A. P. Nanyaro, "Evaluation of the tensor polynomial failure criterion for composite materials," J. Compos. Mater., 12, 63-75 (1978).
12. H. T. Hahn, J. B. Erikson, and S. W. Tsai, "Characterization of matrix interface-controlled strength of unidirectional composites," in: Fracture of Composite Materials (1982), pp. 53-66.
13. R. Jones, Mechanics of Composite Materials (1975).
14. Z. Gürdal, R. T. Haftka, and P. Hajela, Design and Optimization of Laminated Composite Materials (1998).
15. G.A. Seregin and V. A Troitski, "On the best position of elastic symmetry planes in an orthotropic body," Prikl. Matem. Mekh., 45, 139-142 (1982).
16. M. Rovati and A. Taliercio, "Optimal orientation of the symmetry axes of orthotropic 3-D materials," Lecture Notes Eng., 63, 127-134 (1989).
17. D. P. Fyhrie and A. Carter, "Unifying principle of elastic symmetry relating stress to trabecular bone morphology," J. Orthoped. Res., No. 4, 301-317 (1986)
18. P. Pedersen and J. E. Taylor, "Optimal design based on power-law nonlinear elasticity," in: Optimal Design with Advanced Materials, Elsevier, Amsterdam (1993), pp. 51-66.
19. V. D. Hammer, "Strength optimization by fibre orientation," in: Solid Mechanics [in Danish], Tech. Univ. of Denmark.
20. S. W Tsai and H. T. Hahn, Introduction to Composite Materials, Technomic, Westport, Connecticut (1980).