Anisotropie increase in yield strength by straining and baking of bake-hardenable steel

Materials Science Forum

Volumn 495-497, Issue PART 2, 2005, Pages 1485-1492

  Hiwatashi, Shunji ^a   Yonemura, Shigeru ^a  

^a NIPPON STEEL CORPORATION   (Japan)

Author keywords

Anisotropy; Bake hardening; Dislocation pinning; Residual stress; Slip system; Strain path change

Indexed keywords

ANISOTROPY; DISLOCATIONS (CRYSTALS); RESIDUAL STRESSES; STRAIN;

BAKE HARDENING; DISLOCATION PINNING; SLIP SYSTEM; STRAIN-PATH CHANGE;

STEEL;

EID: 35348873390     PISSN: 02555476     EISSN: 16629752     Source Type: Book Series    
DOI: 10.4028/0-87849-975-x.1485     Document Type: Conference Paper

References (19)

1. F.D. Bailey, R.P. Foley and D.K. Matlock: Proceedings of Symposium on High Strength Sheet Steels for the Automotive Industry, edited by R. Pradhan, Iron and Steel Society, Warrendale, PA (1994), p. 119.
2. A. Okamoto, K. Takeuchi and M. Takagi: The Sumitomo Search, September 1989, p. 183.
3. K.-M. Radlmayr, H. Ponschab and M. Blaimschein: in Recent Developments in Sheet Metal Forming Technology, (Proceedings of the IDDRG '94 Open Sessions 18th Biennial Congress), edited by M.J.M. Barata Marques, INETI, Lumiar, Lisboa, Portugal (1994), p. 31.
4. T.N. Seel: SAE Technical Paper Series 910291, SAE, Warrendale, PA (1991).
5. Y. Omiya, K. Kase, I. Tsukatani and Y. Okano: in Sheet Metal Forming Beyond 2000, (Proceedings of the IDDRG 20th Biennial Congress, June 17-19, 1998, Genval, Brussels, Belgium), p. 415.
6. H. Takechi: in Hot- and Cold-Rolled Sheet Steels, edited by R. Pradham and G. Ludkovsky, TMS-AIME, Warrendale, PA (1988), p. 117.
7. W.C. Jeong: Metall. and Mater. Trans. A, Vol. 29A (1998), p. 463.
8. W.T. Roberts and D.V. Wilson: in Recent Developments in Sheet Metal Forming Technology, (Proceedings of the IDDRG'94 Open Sessions 18th Biennial Congress), edited by M.J.M. Barata Marques, INETI, Lumiar, Lisboa, Portugal (1994), p. 67.
9. H. Ishigaki: in Mechanics of Sheet Metal Forming, Material Behavior and Deformation Analysis, Edited by D.P. Koistinen and N.-M. Wang, Plenum Press, New York (1978), p. 315.
10. G. Jun and W.F. Hosford: Metall. Trans. A, Vol. 17A (1986), p. 1573.
11. R. Pradhan: SAE Technical Paper Series 910290, SAE, Warrendale, PA (1991).
12. B.B. Hundy: J. Iron Steel Inst., October 1954, p. 127.
13. M. Blaimschein, K.M. Radlmayr, A. Pichler, E. Till and P. Stiaszny: in Advanced Sheet Metal Forming, (Proceedings of the 19th Biennial IDDRG Congress, June 10-14, 1996, Eger, Hungary), Edited by M. Tisza, The University of Miskolc (1996), p. 445.
14. K.H. Kim and J.J. Yin: J. Mec. Phys. Solids, Vol. 45 (1997) p. 841.
15. E. Aernoudt, J. Gil Sevillano and P. Van Houtte: in Constitutive Relations and Their Physical Basis, (Proceedings of 8th Risø International Symposium on Metallurgy and Materials Science), edited by S.I. Andersen et al, Risø National Laboratory, Roskilde (1987), p. 1.
16. C. Teodosiu: in Modelling of Plastic Deformation and Its Engineering Applications, (Proceedings of 13th Risø International Symposium on Metallurgy and Materials Science), edited by S.I. Andersen et al., Risø National Laboratory, Roskilde (1992), p. 125.
17. E.F. Rauch and J.-H. Schmitt: Mat. Sci. and Eng., Vol. A113 (1989), p. 441.
18. J.L. Raphanel, J.-H. Schmitt and B. Baudelet: Int. J. Plasticity, Vol. 2 (1986), p.371.
19. J.H. Schmitt, E. Aernoudt and B. Baudelet: Mat. Sci. and Eng., Vol. 75 (1984), p. 13.