Abrasive wear properties of tool steel matrix composites in rubber wheel abrasion test and laboratory cone crusher experiments

Wear

Volumn 263, Issue 1-6 SPEC. ISS., 2007, Pages 180-187

  Ala Kleme, Sanna ^a   Kivikytö Reponen, Päivi ^b   Liimatainen, Jari ^b   Hellman, Jussi ^b   Hannula, Simo Pekka ^a,c  

^a AALTO UNIVERSITY   (Finland)

^b Metso Materials Technology   (Finland)

^c VTT TECHNICAL RESEARCH CENTRE OF FINLAND   (Finland)

Author keywords

Abrasive wear; Cemented carbide; Cone crusher; Steel matrix composites; Titanium carbide; Tungsten carbide

Indexed keywords

HARDNESS; MICROSTRUCTURE; TOOL STEEL; TUNGSTEN CARBIDE; VOLUME FRACTION; WEAR RESISTANCE;

ABRASION TEST; CRUSHER CONDITIONS; CRUSHING CONDITIONS; SAND RUBBER WHEEL ABRASION; WEAR MECHANICS;

ABRASION;

ABRASION; HARDNESS; MICROSTRUCTURE; TOOL STEEL; TUNGSTEN CARBIDE; VOLUME FRACTION; WEAR RESISTANCE;

EID: 34748901943     PISSN: 00431648     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.wear.2007.01.111     Document Type: Article

References (12)

1. Zum Gahr K.H. Microstructure and Wear of Materials. Tribology Series vol. 10 (1987), Elsevier, Amsterdam p. 560
2. Moshgbar M., Bearman R.R., and Parkin R. Optimum control of cone crusher utilizing an adaptive strategy for wear compensation. Miner. Eng. 8 4-5 (1995) 367-376
3. Evertsson C.M. Modelling of flow in cone crushers. Miner. Eng. 12 12 (1999) 1479-1499
4. Lindroos V., Hellman J., Lou D., Nowak R., Pagounis E., Liu X.W., and Penttinen I. Designing with metal-matrix composites. In: Totten G., Xie L., and Funatani K. (Eds). Handbook of Mechanical Alloy Design (2003), Marcel Dekker, New York 667-727
5. Lou D., Hellman J., Luhulima D., Liimatainen J., and Lindroos V.K. Interactions between tungsten carbide (WC) particulates and metal matrix in WC-reinforced composites. Mater. Sci. Eng. A A340 (2003) 155-162
6. Berns H. Comparison of wear resistant MMC and white cast iron. Wear 254 (2003) 47-54
7. Pagounis E., Talvitie M., and Lindroos V.K. Microstructure and mechanical properties of hot work tool steel matrix composites produced by hot isostatic pressing. Powder Metall. 40 1 (1997) 55-61
8. Ralph B., Yuen H.C., and Lee W.B. The processing of metal matrix composites-an overview. J. Mater. Process. Technol. 63 (1997) 339-353
9. P. Kivikytö-Reponen, Correlation of material characteristics and wear of powder metallurgical metal matrix composites, Doctoral Thesis, Helsinki University of Technology Doctoral Thesis in Materials and Earth Sciences, TKK-ME-DT-5, Finland, 2006, p. 93.
10. Hawk J.A., Wilson R.D., Tylczak J.H., and Doǧan O.N. Laboratory abrasive wear tests: investigation of test methods and alloy correlation. Wear 225-229 (1999) 1031-1042
11. Pagounis E., Talvitie M., and Lindroos V.K. Influence of reinforcement volume fraction and size on the microstructure and abrasion wear resistance of hot isostatic pressed white iron matrix composites. Metall. Mater. Trans. A 27A (1996) 4171-4181
12. Lindqvist M., and Evertsson D.M. Prediction of worn geometry in cone crushers. Miner. Eng. 16 (2003) 1355-1361