Determination of residual stresses in injection-moulded flat plate: Simulation and experiments

Polymer Testing

Volumn 26, Issue 7, 2007, Pages 862-868

  Kim, Chae Hwan ^a   Youn, Jae Ryoun ^a  

^a Seoul National University   (South Korea)

Author keywords

Incremental hole drilling method; Injection moulding; Layer removal method; Polymeric materials; Residual stress

Indexed keywords

COMPUTER SIMULATION; COMPUTER SOFTWARE; FINITE ELEMENT METHOD; INJECTION MOLDING; PLASTIC PARTS; TEMPERATURE DISTRIBUTION;

FLAT PLATE; INCREMENTAL HOLE-DRILLING METHOD; LAYER-REMOVAL METHOD; RESIDUAL STRESS MEASUREMENTS;

RESIDUAL STRESSES;

EID: 34648820465     PISSN: 01429418     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.polymertesting.2007.05.006     Document Type: Article

References (17)

1. Pötsch G., and Michaeli W. Injection Molding: An Introduction (1995), Hanser Publishers
2. Treuting R.G., and Read W.T. A mechanical determination of biaxial residual stress in sheet. J. Appl. Phys. 22 (1951) 130
3. Hastenberg C.H.V., Wildervanck P.C., Leenen A.J.H., and Schennink G.G.J. The measurement of thermal stress distributions along the flow path in injection-molded flat plates. Polym. Eng. Sci. 32 (1992) 506
4. Zoetelief W.F., Douven L.F.A., and Ingen Housz A.J. Residual thermal stresses in injection molded products. Polym. Eng. Sci. 36 (1996) 1886
5. Kim S.K., Lee S.W., and Youn J.R. Measurement of residual stresses in injection molded short fiber composites considering anisotropy and modulus variation. Korea-Aust. Rheol. J. 14 (2002) 107
6. Jung J.H., Lee S.W., and Youn J.R. Characterization of deformation in injection molded parts after packing and cooling. Macromol. Symp. 148 (1999) 263
7. Mathar J. Determination of initial stresses by measuring the deformation around drilled holes. Iron Steel 56 (1934) 249
8. Annual Book of ASTM E837-01, Determining residual stresses by the Hole-Drilling Strain-Gage Method, 2001.
9. Measurement Group Tech Note TN-503-5, 1996.
10. Wang T.H., and Young W.B. Study on residual stresses of thin-walled injection molding. Eur. Polym. J. 41 (2005) 2511
11. Kawanemi K.K., Vaillancourt H., Wang H., and Salloum G. Residual stresses, shrinkage, and warpage of complex injection molded products: numerical simulation and experimental validation. Polym. Eng. Sci. 38 (1998) 21
12. Maxwell A.S., and Turnbull A. Measurement of residual stress in engineering plastics using the hole-drilling technique. Polym. Test. 22 (2003) 231
13. Sicot O., Gong X.L., Cherouat A., and Lu J. Determination of residual stress in composite laminates using the incremental hole-drilling method. J. Compos. Mater. 37 (2003) 831
14. Schajer G.S. Application of finite element calculations to residual stress measurement. J. Eng. Mater. Technol. 103 (1981) 157
15. Flaman M.T., and Manning B.H. Determination of residual stress variation with depth by the hole-drilling method. Exp. Mech. 25 (1985) 205
16. Schajer G.S. Measurement of non-uniform residual stresses using the hole-drilling method. J. Eng. Mater. Technol. 110 (1988) 338
17. Jansen K.M.B., Orij J.J.W., Meijer C.Z., and Vandijk D.J. Comparison of residual stress predictions and measurements using excimer laser layer removal. Polym. Eng. Sci. 39 (1999) 2030