Deformation of alumina droplets on micro-patterned substrates under plasma spraying conditions

Journal of Thermal Spray Technology

Volumn 16, Issue 2, 2007, Pages 300-305

  Shinoda, Kentaro ^a,b   Yamada, Atsushi ^a,b   Kambara, Makoto ^a,b   Kojima, Yoichi ^a,b   Yoshida, Toyonobu ^a,b  

^a UNIVERSITY OF TOKYO   (Japan)

^b NATIONAL INSTITUTE FOR MATERIALS SCIENCE   (Japan)

Author keywords

Diagnostics and control; RF induction plasma spraying; Roughness effects; Spray deposition

Indexed keywords

IMPACT VELOCITY; MICRO-PATTERNED SUBSTRATES;

ALUMINA; DROPS; INDUCTIVELY COUPLED PLASMA; SPRAYED COATINGS; SUBSTRATES; SURFACE ROUGHNESS;

PLASMA SPRAYING;

EID: 34548776027     PISSN: 10599630     EISSN: None     Source Type: Journal    
DOI: 10.1007/s11666-007-9033-8     Document Type: Review

References (17)

1. K. Shinoda, Y. Kojima, T. Yoshida, In Situ Measurement System for Deformation and Solidification Phenomena of Yttria-Stabilized Zirconia Droplets Impinging on Quartz Glass Substrate Under Plasma Spraying Conditions, J. Therm. Spray Technol., 14(4), 2005, 511-517
2. K. Shinoda, T. Koseki, T. Yoshida, Influence of Impact Parameters of Zirconia Droplets on Splat Formation and Morphology in Plasma Spraying, J. Appl. Phys, 2006, 100(7), Art. No. 074903 (6 pages)
3. N.P. Padture, M. Gell, E.H. Jordan, Materials Science - Thermal Barrier Coatings for Gas-Turbine Engine Applications, Science, 296(5566), 2002, 280-284
4. P. Fauchais, M. Fukumoto, A. Vardelle, M. Vardelle, Knowledge Concerning Splat Formation: An Invited Review, J. Therm. Spray Technol., 13(3), 2004, 337-360
5. C.D. Stow, M.G. Hadfield, An Experimental Investigation of Fluid Flow Resulting from the Impact of a Water Drop with an Unyielding Dry Surface, Proc. R. Soc. Lond. A, 373, 1981, 419-441
6. C. Moreau, P. Gougeon, M. Lamontagne, Influence of Substrate Preparation on the Flattening and Cooling of Plasma-Sprayed Particles, J. Therm. Spray Technol., 4(1), 1995, 25-33
7. K. Range, F. Feuillebois, Influence of Surface Roughness on Liquid Drop Impact, J. Colloid Interface Sci. 203, 1998, 16-30
8. H. Fukanuma, Mathematical Modeling of Flattening Process on Rough Surfaces in Thermal Spray, Thermal Spray: Practical Solutions for Engineering Problems, C.C. Berndt, Ed., Oct 7-11, 1996 (Cincinnati, OH), ASM International, 1996, p 647-656
9. A.M. Ahmed, R.H. Rangel, Metal Droplet Deposition on Non-Flat Surfaces: Effect of Substrate Morphology, Int. J. Heat Mass Transf. 45(5), 2002, 1077-1091
10. M. Fukumoto, M. Ohgitani, T. Yasui, Effect of Substrate Surface Change on Flattening Behaviour of Thermal Sprayed Particles, Mater. Trans., 45(6), 2004, 1869-1873
11. J. Cedelle, M. Vardelle, and P. Fauchais, Influence of Stainless Steel Substrate Preheating on Surface Topography and on Millimeter- and Micrometer-Sized Splat Formation, Surf. Coat. Technol., 2006, 201(3-4), p 1373-1382
12. A. Raessi, J. Mostaghimi, M. Bussmann, Effect of Surface Roughness on Splat Shapes in the Plasma Spray Coating Process, Thin Solid Films, 506, 2006, 133-135
13. C. Josserand, L. Lemoyne, R. Troeger, S. Zaleski, Droplet Impact on a Dry Surface: Triggering the Splash with a Small Obstacle, J. Fluid Mech., 524, 2005, 47-56
14. D. Sivakumar, K. Katagiri, T. Sato, and H. Nishiyama, Spreading Behavior of an Impacting Drop on a Structured Rough Substrate, Phys. Fluids, 2005, 17(10), Art. No. 100608 (10 pages)
15. T. Yoshida, T. Okada, H. Hamatani, H. Kumaoka, Integrated Fabrication Process for Solid Oxide Fuel Cells Using Novel Plasma Spraying, Plasma Sources Sci. Technol., 1(3), 1992, 195-201
16. H. Murakami, T. Yoshida, K. Akashi, High-Rate Thermal Plasma CVD of SiC, Adv. Ceram. Mater., 3(4), 1988, 423-426
17. Y.V. Naidich, R.P. Vorrovich, V.V. Zabuga, Wetting and Spreading in Heterogeneous Solid Surface-Metal Melt Systems, J. Colloid Interface Sci. 174, 1995, 104-111