Multi-step dip-spin coating manufacturing system for silicone cardiovascular membrane fabrication with prescribed compliance

International Journal of Advanced Manufacturing Technology

Volumn 34, Issue 7-8, 2007, Pages 667-679

  Cortez, Miguel A ^a   Quintana, Rolando ^b   Wicker, Ryan B ^a  

^a UNIVERSITY OF TEXAS AT EL PASO   (United States)

^b UNIVERSITY OF TEXAS AT SAN ANTONIO   (United States)

Author keywords

Cardiovascular system modeling; Compliant vessel fabrication; Dip spin coating; Rotational curing; Silicone membranes

Indexed keywords

CARDIOVASCULAR SYSTEM; CURING; DATA ACQUISITION; HEMODYNAMICS; MEDICAL IMAGING; SILICONES; VISCOSITY;

CARDIOVASCULAR SYSTEM MODELING; COMPLIANT VESSEL FABRICATION; ROTATIONAL CURING; SILICONE MEMBRANES;

SPIN COATING;

EID: 34548618216     PISSN: 02683768     EISSN: 14333015     Source Type: Journal    
DOI: 10.1007/s00170-006-0649-5     Document Type: Article

References (19)

1. Herger JW et al (1998) Cardiology. William & Wilkins, Baltimore, MD
2. Ahumada GG (1987) Cardiovascular pathophysiology. Oxford University Press, New York, NY
3. Topol EJ (1998) Textbook of cardiovascular medicine. Lippincot Ravet, New York
4. Willerson JT, Cohn JN (2000) Cardiovascular medicine. Churchill Livingstone, Philadelphia
5. Rhee K, Tarbell JM (1994) A study of the wall shear rate distribution near the end-to-end anastomosis of a rigid graft and compliant artery. J Biomech 27(3):329-338
6. Hopkins LM et al (2000) Particle image velocimetry measurements in complex geometries. Exp Fluids 29:91-95
7. Tai NR, Salacinski HJ, Edwards A, Hamilton G, Seifalian AM (2000) Compliance properties of conduits used in vascular reconstruction. Br J Surg 87:1516-1524
8. DuPont Dow Elastomers (2001) Neoprene latex dipped good technical information. Wilmington, DE
9. Kostlin H, Frank G, Hebbinghaus G, Anding H, Denissen K (1997) Optical filters on linear halogen-lamps prepared by dip-coating. J Non-Cryst Solids 218:347-353
10. Cortez MA (2002) Fabrication of silicone models of cardiovascular systems with prescribed compliance. Master of Science Thesis, University of Texas at El Paso, El Paso, TX
11. Chung TS (1999) Fabrication of multi-layer composite hollow fiber membranes for gas separation. J Membr Sci 152:211-225
12. Montgomery DC (1997) Design and analysis of experiments. Wiley, New York
13. Stevanov M, Baruthio J, Eclancher B (2000) Fabrication of elastomer arterial models with specified compliance. J Appl Physiol 88:1291-1294
14. White R, Klein S, Shors E (1987) Preservation of compliance in a small diameter microporous, silicone rubber vascular prosthesis. J Cardiovasc Surg 28:485-490
15. Abbott W, Megerman J, Hasson J, L'Italien G, Warnock D (1987) Effect of compliance mismatch on vascular graft patency. J Vasc Surg 5:376-382
16. Uchida N, Kambic H, Emoto H, Chen JF, Hsu SH, Marabayshi S, Harasaki H, Nose Y (1993) Compliance effect on small diameter polyurethane graft patency. J Biomed Materi Res 27:1269-1279
17. Gryna FM (2001) Quality planning and analysis: from product development through use, McGraw Hill Irwin, New York
18. Wicker RB, Medina F (2003) Framework for physical modeling of complex internal flow passages using rapid prototyping and water-soluble molds. Proceedings of the 31st International Conference on Computers and Industrial Engineering, San Francisco, CA, February 2-4, 2003, pp 559-564
19. Wicker RB, Cortez M, Medina F, Palafox G, Elkins CJ (2001) Manufacturing complex compliant cardiovascular system models for in vitro hemodynamic experimentation using CT and MRI data and rapid prototyping technologies. Proceedings of the 2001 Summer Bioengineering Conference, ASME Bioengineering Division (BED) 50:469-470