Effects of platelet size and mean volume fraction on platelet orientation and volume fraction distributions in functionally graded material fabricated by a centrifugal solid-particle method

Journal of Engineering Materials and Technology

Volumn 129, Issue 2, 2007, Pages 304-312

  Sequeira, P D ^a   Watanabe, Yoshimi ^b   Eryu, Hiroyuki ^c   Yamamoto, Tetsuya ^c   Matsuura, Kiyotaka ^d  

^a UNIVERSITY OF MINHO   (Portugal)

^b NAGOYA INSTITUTE OF TECHNOLOGY   (Japan)

^c SHINSHU UNIVERSITY   (Japan)

^d HOKKAIDO UNIVERSITY   (Japan)

Author keywords

Centrifugal solid particle method; Functionally graded material (FGM); Hermans orientation parameter; Orientation; Platelet

Indexed keywords

ELEMENTARY PARTICLES; FABRICATION; PARAMETER ESTIMATION; PARTICLE SIZE;

CENTRIFUGAL SOLID PARTICLE METHODS; FUNCTIONALLY GRADED MATERIALS (FGM); HERMANS ORIENTATION PARAMETER; PLATELET ORIENTATION;

VOLUME FRACTION;

EID: 34249898666     PISSN: 00944289     EISSN: None     Source Type: Journal    
DOI: 10.1115/1.2712467     Document Type: Article

References (17)

1. Miyamoto, Y., Kaysser, W. A., Rabin, B. H., and Ford, R. G., 1999, Functionally Graded Materials, Design, Processing and Applications, Kluwer, Dordrecht.
2. Fukui, Y., 1991. "Fundamental Investigation of Functionally Gradient Material Manufacturing System Using Centrifugal Force," JSME Int. J., Ser. III, 34(1), pp. 144-148.
3. Watanabe, Y., and Fukui, Y., 2000, "Microstructures and Mechanical Properties of Functionally Graded Material Fabricated by a Centrifugal Method," Recent Res. Dev. Metall. Mater. Sci., 4, pp. 51-93.
4. Fukui, Y., and Watanabe, Y., 1996, "Analysis of Thermal Residual Stress in a Thick-Walled Ring of Duralcan Base Al-SiC Functionally Graded Material," Metall. Mater. Trans. A, 27A(12), pp. 4145-4151.
5. Watanabe, Y., Yamanaka, N., and Fukui, Y., 1998, "Control of Composition Gradient in a Metal-Ceramics Functionally Graded Material Manufactured by the Centrifugal Method," Composites, Part A, 29A(5,6), pp. 595-601.
6. 3Ti Functionally Graded Material Manufactured by Centrifugal Method," Z. Metallkd., 88(9), pp. 717-721.
7. 3Ti Composite Manufactured by a Centrifugal Method," Metall. Mater. Trans. A, 30A(12), pp. 3253-3261.
8. 3Ti Platelet in Al based FGMs Fabricated by a Centrifugal Casting Technique," Acta Mater., 49(5), pp. 775-783.
9. Pipes, R. B., McCullough. R. L., and Taggart, D. G., 1982, "Behavior of Discontinuous Fiber Composites: Fiber Orientation," Polym. Compos., 3(1), pp. 34-39.
10. Wetherhold, R. C, and Scott, P. D., 1990, "Prediction of Thermoelastic Properties in Short Fiber Composites Using Image Analysis Techniques," Compos. Sci. Technol., 37(4), pp. 393-410.
11. 3Ti FGMs Fabricated by a Centrifugal Method," Ceram. Trans., 114, pp. 675-682.
12. DeHoff, R. T, and Rhines, F N., 1968, Quantitative Microscopy, McGraw-Hill, New York.
13. Watanabe, Y., Kawamoto, A., and Matsuda, K., 2002, "Particle Size Distributions of Functionally Graded Materials Fabricated by a Centrifugal SolidParticle Method," Compos. Sci. Technol., 62(6), pp. 881-888.
14. Watanabe, Y., Miyazaki, E., and Okada, H., 2002, "Enhanced Mechanical Properties of Fe-Mn-Si-Cr Shape Memory Fiber/Plaster Smart Composite," Compos. Sci. Technol., 43(5), pp. 974-983.
15. McGee, S. H., and McCullough, R. L., 1984, "Characterization of Fiber Orientation in Short-Fiber Composites," J. Appl. Phys., 55(5), pp. 1394-1403.
16. Gonzalez, L. M., Cumbrera, F., Sanchez-Bajo, F., and Pajares, A., 1994, "Measurement of Fiber Orientation in Short-Fiber Composites," Acta Metall. Mater., 42(3), pp. 689-694.
17. Torii, S., Tanaka, S., Yano, T, and Watanabe, Y. 2004, "Experimental and Theoretical Study on Suspended Particle Motion in Axially Rotating Drum," Int. J. Transp. Phenom., 6(3), pp. 189-195.