Investigation of chip-back temperature during machining depending on cutting parameters

Materials and Design

Volumn 28, Issue 8, 2007, Pages 2329-2335

  Korkut, Ihsan ^a   Boy, Mehmet ^b   Karacan, Ismail ^b   Seker, Ulvi ^a  

^a GAZI UNIVERSITY   (Turkey)

^b ZONGULDAK KARAELMAS UNIVERSITY   (Turkey)

Author keywords

Cutting parameters; Machining; Temperature; Thermal camera; Thermocouple method

Indexed keywords

MACHINING; METAL CUTTING; STAINLESS STEEL; TEMPERATURE MEASUREMENT; THERMOCOUPLES;

CHIP BRAKER; CHIP-BACK TEMPERATURE; CUTTING SPEED; THERMAL CAMERA;

CUTTING TOOLS;

CUTTING TOOLS; MACHINING; METAL CUTTING; STAINLESS STEEL; TEMPERATURE MEASUREMENT; THERMOCOUPLES;

EID: 34249054731     PISSN: 02613069     EISSN: 18734197     Source Type: Journal    
DOI: 10.1016/j.matdes.2006.07.009     Document Type: Article

References (15)

1. Bever M.B., Marshall E.R., and Ticknor L.B. The energy stored in metal chips during ortogonal cutting. J Appl Phys 24 (1953) 1176-1179
2. Shaw M.C. Metal cutting principles (1984), Oxford University Press, London p. 251-92
3. Da-Silva M.B., and Wallbank J. Cutting temperature: prediction and measurement methods a review. J Mater Process Technol 88 (1999) 195-202
4. Bootthrody G. Fundamentals of metal machining and machine tools (1981), McGraw-Hill, New York p. 92-102
5. Grzesik W. Experimental investigation of the cutting temperature when turning with coated indexable inserts. Int J Mach Tool Manu 39 (1999) 355-369
6. Milikic D, Kovac P, Gostrimirovic M. Some aspects of coated hard metal inserts. Balkantrib'96 second international conference on tribology, proceedings, 5-7 June 1996, Thessalonica, Greece.
7. Kolb MG. Influence microemulsions on the uranium machining process. Balkantrib'96 second international conference on tribology, proceedings, 5-7 June 1996, Thessalonica, Greece.
8. Rall D.L., and Giedt W.H. Heat transfer and temperature distribution in a metal cutting tool. Trans ASME 78 (1956) 1507-1515
9. Kuster K.J. Das temperaturfeld in drehmeissel (the temperature field in the cutting edge of cutting tool) (1954), Verlag W. Girardet, Essen, Germany p. 67-71
10. Qureshi A.H., and Koenigsberger F. An investigation into the problem of measuring the temperature distribution on the rake face of a cutting tool. Ann CIRP 14 (1966) 189-199
11. O'Sullivan D., and Cotterell M. Temperature measurement in single point turning. J Mater Process Technol 118 (2001) 301-308
12. Kitigawa T., Kubo A., and Maekawa K. Temperature and wear cutting tools in high speed machining of Inconel 718 of difficult materials. Wear 202 (1996) 142-148
13. TS 10329 (ISO 3685), Torna Kalemleri-Ömür Deneyi, Türk Standartlari{dotless} Enstitüsü, 1992 [in Turkish].
14. Trent E.M. Metal Cutting. second ed. (1984), Butterworth, London
15. Young H.T., and Chou T.L. Investigation of edge effect from the chip-back temperature using IR thermographic techniques. J Mater Process Technol 52 (1995) 213-224