Evaluation of chip morphology in hard turning using constitutive models and material property data

Journal of Manufacturing Science and Engineering

Volumn 129, Issue 1, 2007, Pages 41-47

  Poulachon, Gérard ^a   Moisan, Alphonse L ^a   Jawahir, I S ^b  

^a ENSAM   (France)

^b UNIVERSITY OF KENTUCKY   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

BEARING CAPACITY; MATHEMATICAL MODELS; MICROPROCESSOR CHIPS; STRESS CONCENTRATION; TURNING;

BEARING STEELS; CHIP MORPHOLOGY; HARD TURNING; MACHINING OPERATIONS;

MACHINABILITY;

EID: 34248223719     PISSN: 10871357     EISSN: None     Source Type: Journal    
DOI: 10.1115/1.2335850     Document Type: Article

References (38)

1. Merchant, M. E., 1945, "Mechanics of the Metal Cutting Process - II: Plasticity Conditions in Orthogonal Cutting," J. Appl. Phys., 16, pp. 318-324.
2. Ceretti, E., Fallboehmer, P., Wu, W. T., and Altan, T., 1996, "Application of 2-DFEM to Chip Formation in Orthogonal Cutting," J. Mater. Process. Technol., 59, pp. 169-191.
3. Marusich, T. D., and Ortiz, M., 1995, "Modeling and Simulation of High Speed Machining," Int. J. Numer. Methods Eng., 38, pp. 3675-3694.
4. Ueda, K., and Watanabe, K., 1993, "Rigid-Plastic FEM Analysis of Three-Dimensional Deformation Field in the Chip Formation Process," CIRP Ann., 42, pp. 169-181.
5. Maekawa, K., Ohhata, H., Kitigawa, T., and Childs, T. H. C., 1996, "Simulation Analysis of Machinability of Leaded Cr-Mo and Mn-B Structural Steels," J. Mater. Process. Technol., 62, pp. 363-369.
6. Rakotomolala, R., Joyot, P., and Touratier, M., 1993, "Arbitrary Lagrangian-Eulerian Thermomechanical Finite Element Model of Material Cutting," Commun. Numer. Methods Eng., 9, pp. 975-987.
7. Movahhedy, M. R., Gada, M. S., and Altintas, Y., 2000, "Simulation of Chip Formation in Orthogonal Metal Cutting Process: An Ale Finite Element Approach," Mach. Sci. Technol., 4, pp. 15-42.
8. Athavale, S. M., and Stenkowski, J. S., 1998, "FEM of Machining: From Proof-of-Concept to Engineering Applications," Mach. Sci. Technol., 2, pp. 317-342.
9. Jawahir, I. S., Dillon, O. W., Baladji, A. K., Redetzky, M., and Fang, N., 1998, "Predictive Modelling of Machining Performance in Turning Operations," Mach. Sci. Technol., 2, pp. 253-276.
10. van Luttervelt, C. A., Childs, T. H. C., Jawahir, I. S., Klocke, F., and Venuvinod, P. K., 1998, "Present Situation and Future Trends in Modelling of Machining Operations," CIRP Ann., 47, pp. 587-626.
11. Berns, H., Liu, J., and Theisen, W., 1996, "A New Experimental Approach to Metal Cutting," Z. Metallkd., 87, pp. 418-423.
12. Sutter, G., Molinari, A., Delime, A., Dudzinski, D., and Faure, L., 1997, "High Speed Machining Experiments," First French and German Conference on High Speed Machining, Metz, France, June, pp. 453-459.
13. Johnson, G. R., and Cook, W. H., 1985, "Fracture Characteristics of Three Metals Subjected to Various Strains, Strain Rates, Temperature, and Pressure, Eng. Fract. Mech., 21, pp. 31-48.
14. Zerilli, F. J., and Armstrong, R. W., 1987, "Dislocation-Mechanics- Based Constitutive Relations for Material Dynamics Calculations," J. Appl. Phys., 61, pp. 1816-1825.
15. Goldthorpe, B. D., and Church, P., 1997, "Mechanical and Physical Behavior of Materials Under Dynamic Loading," J. Phys. IV, 7, pp. 753-759.
16. Harding, J., 1987, "The Effects of High Strain Rate on Material Properties," Elsevier, Barking, UK, pp. 133-186.
17. Shirakashi, T., Maekawa, K., and Usui, E., 1983, "Flow Stress of Low Carbon Steel at High Temperature and Strain Rate (Part 1) - Property of Incremental Strain Method in Impact Compression Test With Rapid Heating and Cooling Systems," Bull. Jpn. Soc. Precis. Eng., 17, pp. 161-166.
18. Maekawa, K., Shirakashi, T., and Usui, E., 1983, "Flow Stress of Low Carbon Steel at High Temperature and Strain-Rate (Part 2) - Flow Stress Under Variable Temperature and Variable Strain Rate," Bull. Jpn. Soc. Precis. Eng., 17, pp. 167-172.
19. Childs, T. H. C., 1997, "Material Properly Requirements for Modelling Metal Machining," J. Phys. IV, 7, pp. 21-36.
20. Narutaki, N., and Yamane, Y., 1979, "Tool Wear and Cutting Temperature of CBN Tools in Machining of Hardened Steels," CIRP Ann., 28, pp. 23-28.
21. Ohtani, T., and Yokogawa, H., 1988, "The Effects of Workpiece Hardness on Tool Wear Characteristics," Bull. Jpn. Soc. Precis. Eng., 22, pp. 229-231.
22. Matsumoto, Y., Barash, M. M., and Liu, C. R., 1987, "Cutting Mechanism During Machining of Hardened Steel," Mater. Sci. Eng., 3, pp. 299-305.
23. Poulachon, G., and Moisan, A., 2000, "Hard Turning: Cutting Mechanisms and Metallurgical Aspects," ASME J. Manuf. Sci. Eng., 122, pp. 406-412.
24. Toenshoff, H. K., Arendt, C., and Ben Amor, R., 2000, "Cutting Hardened Steel," CIRP Ann., 49, pp. 1-19.
25. Poulachon, G., Moisan, A., and Jawahir, I. S., 2001, "The Influence of Thermo-Mechanical Behavior in Chip Formation During Hard Turning of 100Cr6 Bearing Steel," CIRP Ann., 50, pp. 31-36.
26. Vicente, H., Decultieux, F., Levaillant, C., Schmidt, P., and Svensson, I. L., 1995, "Mushy Zone Behaviour: Rheological Characterization and Influence on Air Gap Formation," Iron and Steel Institute of Japan, Vol. 35.
27. Poulachon, G., and Moisan, A., 1998, "A Contribution to the Study of the Cutting Mechanisms During High Speed Machining of Hardened Steel," CIRP Ann., 47, pp. 73-76.
28. Komanduri, R., and Brown, R. H. 1981, "The Mechanics of Chip Segmentation in Machining," ASME J. Eng. Ind., 103, pp. 33-51.
29. Wright, P. K., and Trent, E. M. 1973, "Metallographic Methods of Determining Temperature Gradients in Cutting Tools," J. Iron Steel Inst., London, 211, pp. 364-368.
30. Zener, C., and Hollomon, J., 1944, "Effect of Strain Rate Upon Plastic Flow of Steel," J. Appl. Phys., 15, pp. 22-32.
31. Recht, R. F., 1964, "Catastrophic Thermoplastic Shear," J. Appl. Phys., 31, pp. 189-193.
32. Loewen, E. G., and Shaw, M. C., 1954, "On the Analysis of Cutting Tool Temperature," Trans. ASME, 76, pp. 217-231.
33. Stevenson, R., 1999, "Material Properties as Indicators of Machining Behavior," ASME J. Manuf. Sci. Eng., 10, pp. 197-203.
34. Ozel, T., and Altan, T., 2000, "Determination of Workpiece Flow Stress and Friction at the Chip-Tool Contact for High-Speed Cutting," Int. J. Mach. Tools Manuf., 40, pp. 133-152.
35. Komanduri, R., Schroeder, T., Hazra, J., von Turkovitch, B. F., and Flom, D. G., 1982, "On the Catastrophic Shear Instability in High-Speed Machining of an AISI 4340 Steel," J. Eng. Ind., 104, pp. 121-131.
36. Xie, J. Q., Bayoumi, A. E., and Zbib, H. M., 1996, "A Study on Shear Banding in Chip Formation of Orthogonal Machining," Int. J. Mach. Tools Manuf., 36, pp. 835-847.
37. Hou, Z. B., and Komanduri, R., 1997, "Modeling of Thermomechanical Shear Instability in Machining," Int. J. Mech. Sci., 39, pp. 1273-1314.
38. Umbrello, D., Hua, J., and Shivpuri, R., 2005, "Modeling of the Flow Stress for AISI 52100 Bearing Steel During Hard Machining Processes," Int. J. Forming Processes, Hermes Sci Publications, Vol. 8/SI-2005, pp. 363-379.