Measurement of ductile forming limit in non-linear strain paths and anisotropic yield conditions for 11% Cr steel sheets

ISIJ International

Volumn 47, Issue 1, 2007, Pages 122-130

  Iguchi, Takaaki ^a   Yanagimoto, Jun ^b  

^a JFE STEEL CORPORATION   (Japan)

^b INSTITUTE OF INDUSTRIAL SCIENCE   (Japan)

Author keywords

11 Cr steel; Anisotropy; Forming limit; Sheet forming; Yield criterion

Indexed keywords

ANISOTROPY; CHROMIUM; DUCTILITY; FRACTURE TOUGHNESS; STRAIN RATE; STRESS ANALYSIS;

FORMING LIMIT; NONLINEAR STRAIN PATHS; SHEET FORMING; YIELD CRITERION;

STEEL SHEET;

EID: 34247259851     PISSN: 09151559     EISSN: None     Source Type: Journal    
DOI: 10.2355/isijinternational.47.122     Document Type: Article

References (33)

1. K. Nakajima: J. Mater. Process. Technol., 11 (1970), No. 109, 112.
2. H. J. Kleemola and M. T. Pelkkikangas: Sheet Met. Ind., 63 (1977), 591.
3. H.W. Swift: J. Mech. Phys. Solids, 1 (1952), 1.
4. R. Hill: J. Mech. Phys. Solids, 1 (1952), 19.
5. S. Stören and J. R. Rice: J. Mech. Phy. Solids, 23 (1975), 421.
6. J. Christoffersen and J. W. Hutchinson: J Mech. Phy. Solids, 27 (1979), 465.
7. M. Gotoh: Trans. Jpn. Soc. Mech. Eng. A, 47 (1981), No. 424, 1389.
8. M. Gotoh: Trans. Jpn. Soc. Mech. Eng. A, 48 (1982). No. 428, 493.
9. M. Gotoh: Trans. Jpn. Soc. Mech. Eng. A, 48 (1982), No. 428, 502.
10. M. Gotoh: Trans. Jpn. Soc. Mech. Eng. A, 49 (1983), No. 437, 92.
11. M. Gotoh: Trans. Jpn. Soc. Mech. Eng. A, 50 (1984). No. 458, 1753.
12. M. Goya and K. Ito: Trans. Jpn. Soc. Mech. Eng. A, 54 (1988), No. 504, 1617.
13. M. Goya and K. Ito: Trans. Jpn. Soc. Mech. Eng. A, 56 (1990). No. 521, 101.
14. N. Iwata, M. Matsui and M. Gotoh: J. Jpn. Soc. Technol. Plast., 33 (1992). No. 381, 1196.
15. N. Iwata, M. Matsui and M. Gotoh: J. Jpn. Soc. Technol. Plast., 33 (1992), No. 381, 1202.
16. T. Yoshida, K. Ito, Y. Kuriyama and M. Usuda: J. Jpn. Soc. Technol. Plast., 42 (2001), No. 488, 919.
17. T. Kuwabara, M. Kuroda. V Tvergaard and K. Nomura: Acta Mater, 48 (2000), No. 9, 2071.
18. H. Takuda, K. Mori, H. Fujimoto and N. Hatta: Arch. Appl. Mech., 67 (1997), 143.
19. H. Takuda, K. Mori and N. Hatta: J. Mater. Process. Technol., 95 (1999), 116.
20. J. Gronostajski: J. Mech. Work. Technol., 10 (1984), 349.
21. R. Arrieux: Ann. CIRP, 36 (1987), No. 1, 195.
22. L. Zhao, R. Sowerby and M. P. Sklad: Int. J. Mech. Sci., 38 (1996). 1307.
23. T. B. Stoughton: Int. J. Mech. Sci., 42 (2000), 1.
24. K. Yoshida and T. Kuwabara: Tetsu-to-Hagané, 92 (2006). No. 1, 36.
25. K. Yoshida, T. Kuwabara, K. Narihara and S. Takahashi: J. Jpn. Soc. Technol. Plast., 45 (2004), No. 517, 123.
26. R. H. Wagoner: Metall. Trans. A, 12A (1981), 877.
27. R. W. Logan and W. F. Hosford: Int. J. Mech. Sci., 22 (1980), 419.
28. R. Hill: Proc. R. Soc. (London), A193 (1948), 281.
29. A. J. Ranta-Eskola: Int. J. Mech. Sci., 21 (1979). 457.
30. T. Kuwabara, S. Yamada, E. Iizuka and T. Hira: Tetsu-to-Hagane, 87 (2001), No. 4, 40.
31. T. Kuwabara and S. Ikeda: Tetsu-to-Hagane, 88 (2002), No. 6, 50.
32. F. Barlat, J. C. Brem, J. W. Yoon, K. Chung, R. E. Dick, D. J. Lege, F. Pourboghrat, S.-H. Choi and E. Chu: Int. J. Plast., 19 (2003), 1297.
33. S. Ikeda and T. Kuwabara: Japanese Spring Conf. for the Technology of Plasticity, JSTP, Tokyo, (2003), 229.