Study of mechanical behavior of molybdenum coating using sliding wear and impact tests

Wear

Volumn 262, Issue 11-12, 2007, Pages 1330-1336

  Laribi, M ^a   Vannes, A B ^b   Treheux, D ^b  

^a ECOLE NATIONALE POLYTECHNIQUE   (Algeria)

^b LABORATOIRE DE TRIBOLOGIE ET DYNAMIQUE DES SYSTÈMES   (France)

Author keywords

Flame spraying; Friction resistance; Impact test; Lubrication; Molybdenum; Post annealing

Indexed keywords

FLAME SPRAYING; FRICTION; IMPACT TESTING; LUBRICATION; MOLYBDENUM; PROTECTIVE COATINGS;

FRICTION RESISTANCE; POST ANNEALING; TRIBOLOGICAL RESISTANCE;

WEAR OF MATERIALS;

FLAME SPRAYING; FRICTION; IMPACT TESTING; LUBRICATION; MOLYBDENUM; PROTECTIVE COATINGS; WEAR OF MATERIALS;

EID: 34247121410     PISSN: 00431648     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.wear.2007.01.018     Document Type: Article

References (18)

1. Stolarski T.A., and Tobe S. The effect of spraying distance on wear resistance of molybdenum coatings. Wear 249 (2001) 1096-1102
2. Lesage J., Chicot D., Judas D., Zampronio M., et al. Interfacial indentation measurements of adhesion of thermal sprayed NiCr coatings. Matériaux et Tech. 9-10 (1999) 29-34 (in French)
3. Herman H., Sampath S., and Mccune R. Thermal Spray: Current Status and Future Trends. MRS Bulletin vol. 25 (7) (2000), Materials Research Society
4. Molybdenum 99E coating characteristics, Technical Bulletin of Metalisation Spray Co. (7/03-96).
5. Bouzakis K.D., Vidakis N., and David K. The concept of an advanced impact tester supported by evaluation software for the fatigue strength characterisation of hard layered media. Thin solid films 355-356 (1999) 322-329
6. Bouzakis K.D., Asimakopoulos A., Michailidis N., et al. The inclined impact test, an efficient method to characterise coatings' cohesion and adhesion properties. Thin Solid Films 469-470 (2004) 254-262
7. Bouzakis K.D., Lontos A., Vidakis N., et al. Determination of creep behaviour of monolayer thick plasma sprayed coatings, by means of the impact test and analytical FEM supported evaluation procedure. Thin Solid Films 377-378 (2000) 373-381
8. Iordanova I., Forcey K.S., Gergov B., and Bojinov V. Characterization of flame-sprayed and plasma-sprayed pure metallic and alloyed coatings. Surf. Coat. Technol. 72 (1995) 23-29
9. Laribi M., Vannes A.B., Mesrati N., and Treheux D. Metallurgical characterisation and determination of residual stresses of coatings formed by thermal spraying. Int. J. Therm. Spray Technol. 12 2 (2003) 234-239
10. Laribi M., Mesrati N., Laracine M., Vannes A.B., and Treheux D. Experimental determinations of residual stresses of structures elaborated by thermal spraying. Matériaux et Tech. J. 9-10 (2001) 15-21 (in French)
11. Laribi M., Vannes A.B., and Treheux D. On a determination of wear resistance and adhesion of molybdenum, Cr-Ni and Cr-Mn steel coatings thermally sprayed on a 35CrMo4 steel. J. Surf. Coat. Technol. 200 (2006) 1704-1710
12. Laribi M., Mesrati N., Vannes A.B., and Treheux D. Adhesion and residual stresses determination of thermally sprayed molybdenum on steel. J. Surf. Coat. Technol. 166 (2003) 206-212
13. Edrisy A., Perry T., Cheng Y.T., and Alpas A.T. Wear of thermal spray deposited low carbon steel coatings on aluminum alloys. Wear 251 (2001) 1023-1033
14. Jahanmir S., Abrahamson D.E., Ives L.K., and Suh N.P. Sliding wear resistance of metallic coated surfaces. Wear 40 (1976) 75-84
15. Wayne S.F., Sampath S., and Anand V. Wear mechanisms in thermally sprayed Mo-based coatings. Tribol. Trans. 37 3 (1994) 636
16. Bouzakis K.D., Siganos A., Leyendecker T., and Erkens G. Thin hard coatings fracture propagation during the impact test. Thin Solid Films 460 (2004) 181-189
17. Bartz W.J. Tribology, lubricants and lubrication engineering. Wear 49 1 (1978) 1-18
18. Wang X.Y., Zhang H., and Li D.Y. Characterisation of lubricated worn surfaces using a nano/micro-indenter. Mater. Sci. Eng. A 371 1-2 (2004) 222-228