Electro-discharge machining performance of TiCN-based cermets

International Journal of Refractory Metals and Hard Materials

Volumn 25, Issue 4, 2007, Pages 293-299

  Manoj Kumar, B V ^a   Ramkumar, J ^a   Basu, Bikramjit ^a   Kang, S ^b  

^a INDIAN INSTITUTE OF TECHNOLOGY KANPUR   (India)

^b Seoul National University   (South Korea)

Author keywords

Cermet; EDM; Secondary carbide; Wear

Indexed keywords

CARBIDES; ELECTRIC DISCHARGE MACHINING; SCANNING ELECTRON MICROSCOPY; SOLIDIFICATION; SURFACE ROUGHNESS; TITANIUM COMPOUNDS;

ELECTRO-DISCHARGE MACHINING; MATERIAL REMOVAL RATE (MRR); SECONDARY CARBIDE; TOOL WEAR RATIO (TWR);

CERMETS;

EID: 34147171717     PISSN: 02634368     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.ijrmhm.2006.07.001     Document Type: Article

References (23)

1. Petrofes N.F., and Gadalla A.M. Processing aspects of shaping advanced materials by electrical discharge machining. Adv Mater Manuf Process (1988) 127-153
2. Arthur A, Dickens PM, Cobb RC. Rapid Prototyping J 196;2(1):4.
3. Wang W.F. Powder Metall 40 4 (1997) 295
4. Johnson J.L., and German R.M. Int J Powder Metall 30 1 (1994) 91
5. Tsai H.C., Yan B.H., and Huang F.Y. EDM performance of Cr/Cu-based composite electrodes. Int J Mach Tools Manf 43 (2003) 245-252
6. Li L., Wong Y.S., Fuh J.Y.H., and Lu L. EDM performance of TiC/copper-based sintered electrodes. Mater Des 22 (2001) 669-678
7. Luis C.J., Puertas I., and Villa G. Material removal rate and electrode wear study on the EDM of silicon carbide. J Mater Proc Tech 164-165 (2005) 889-896
8. 4-TiN composites. J Eur Ceram Soc 9 (1992) 83-93
9. Pitman A., and Huddleston J. Electrical discharge machining ZrO2/TiN particulate composite. Bs4r Ceram Trans 99 (2000) 77-84
10. Lauwers B., Kruth J.P., Liu W., Eeraerts W., Schcht B., and Bleys P. Investigation of material removal mechanisms in EDM of ceramic composite materials. J Mater Proc Tech 149 (2004) 347-352
11. 0.5 particles for electrical discharge machining. Mat Sci Forum 492-493 (2005) 27-32
12. Sanchez J.A., Cabanes I., Lopez de Lacalle L.N., and Lamikiz A. Development of optimum electro-discharge machining technology for advanced ceramics. Int J Adv Manuf Tech 18 12 (2001) 897-905
13. Matsuo T., and Oshiwa E. Investigation on the optimum carbide content and machining conditions for wire EDM of zirconia ceramics. Ann CIRP 41 1 (1992) 231-234
14. 4 composite. Ceram Int 29 (2003) 679-687
15. Mahdavinejad R.A., and Mahdavinejad A. ED machining of WC-Co. J Mater Proc Tech 162-163 (2005) 637-643
16. Zhang S. Titanium carbonitride - based cermets: process and properties. Mater Sci Engg A 163A (1993) 141-148
17. D'Errico G.E., Buglisosi E., and Guglielmi E. Tool-life reliability of cermet inserts in milling tests. J Mat Proc Tech 77 (1998) 337-343
18. Kwon W.T., Park J.S., Kim S.-W., and Kang S. Effect of WC and group IV carbides on the cutting performance of Ti(CN) cermet tools. Intl J Mach Tools Manf 44 (2004) 341-346
19. Ettmayer P., Kolaska H., Lengauer W., and Dreyer K. Ti(CN) cermets: metallurgy and properties. Int J Refract Met H 13 (1995) 343-351
20. 0.3)-30Ni system. Int J Refr Met Hard Mat 19 (2001) 539-545
21. Qi F., and Kang S. A study on microstructural changes in Ti(CN)-NbC-Ni cermets. Mater Sci Engg A 251 (1998) 276-285
22. Ahn S., and Kang S. Formation of core/Rim Structures in Ti(C,N)-WC-Ni cermets via a dissolution and precipitation process. J Am Ceram Soc 83 6 (2000) 1489-1494
23. Anstis G.R., Chantikul P., Lawn B.R., and Marshall D.B. A critical evaluation of indentation techniques for measuring fracture toughness: I. Direct crack measurements. J Am Cer Soc 64 (1981) 533