Towards the three-dimensional FE analysis of rapid prototyping tools for sheet metal stamping process

Finite Elements in Analysis and Design

Volumn 43, Issue 8, 2007, Pages 611-619

  Oudjene, M ^a   Penazzi, L ^b   Batoz, J L ^c  

^a GIP InSIC   (France)

^b ECOLE DES MINES D ALBI CARMAUX   (France)

^c UNIVERSITÉ DE TECHNOLOGIE DE COMPIÈGNE   (France)

Author keywords

Contact forces; FEM; Joining; Layered tooling; Rapid prototyping; Stamping process

Indexed keywords

COMPUTER SIMULATION; ELASTIC DEFORMATION; FINITE ELEMENT METHOD; MATHEMATICAL MODELS; METAL STAMPING; SHEET METAL;

CONTACT FORCES; LAYERED TOOLING; STAMPING PROCESS;

RAPID PROTOTYPING;

EID: 34147108163     PISSN: 0168874X     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.finel.2006.12.012     Document Type: Article

References (20)

1. Nakagawa T. Advanced in prototype and low volume sheet forming and tooling. J. Mater. Process. Tech. 98 (2000) 244-250
2. D.H. Mueller, H. Mueller, Rapid Prototyping Techniques to Manufacture Sheet Metal Forming Tools, ISATA, Dublin, Ireland, 2000.
3. M. Oudjene, J.-L. Batoz, F. Mercier, L. Penazzi, C. Pelaingre, Mechanical analysis of prototyping tools for sheet metal stamping, in: Proceedings of RPD2004-Advanced Solutions and Development, Marinha Grande, Portugal, October 12-13, 2004.
4. Muller H., and Sladojevic J. Rapid tooling approaches for small lot production of sheet metal parts. J. Mater. Process. Tech. 115 (2001) 97-105
5. Walczyk D.F., and Hardt D.H. Design and analysis of reconfortable discrete dies for sheet metal forming. J. Manuf. Syst. 17 6 (1998) 436-454
6. Walczyk D.F., and Hardt D.H. Rapid tooling for sheet metal forming using profiled edge laminations-design principles and demonstration. J. Manuf. Syst. 120 (1998) 746-754
7. Walczyk D.F., and Hardt D.H. A comparison of rapid fabrication methods for sheet metal forming dies. J. Manuf. Syst. 121 (1999) 214-224
8. Dickens P.M. Principles of design for laminated tooling. Int. J. Prod. Res. 35 N5 (1997) 1349-1357
9. C. Abel, L. Velnom, C. Barlier, P. Poirier, FASTOOL et MOLSTRA, Deux projets européens de recherche collaborative en PME (CRAFT)-intégration du procédé de Stratoconception en outillage rapide direct pour l'injection, l'emboutissage et la fonderie sous pression, Micad 2003, Paris 1-3 avril 2003.
10. Wadman B. Fluid cell forming tools produced by different rapid prototyping methods. Proceedings of the 22th International Deep Drawing Research Group Congress, Bled, Slovenia (2003) 205-214
11. M. Oudjene, F. Mercier, L. Penazzi, J.-L. Batoz, 3D finite element modeling and analysis of the laminated tooling behaviour in sheet metal stamping process, in: Proceedings of the 24th International Deep Drawing Research Group Congress, Besanćon, France, June 20-22, 2005.
12. M. Oudjene, Modélisation et optimisation du comportement mécanique des outils d'emboutissage stratifiés précontraints par vissage, Ph.D. Thesis, Institut National Polytechnique de Lorraine, Nancy, France, 2005.
13. Pepelnjak T., and Kuzman K. Adaptable tooling sets for metal forming of geometrically similar products. J. Mater. Process. Tech. 80-81 (1998) 413-420
14. Dankert J. Reduction of the residual stresses in a deep-drawing cup by modifying the draw die profile. Ann. CIRP 44/1/ (1995)
15. F.F. Damborg, M.R. Jensen, K.B. Nielsen, J. Dankert, Optimization of the draw die profile with regard to wear using the FEM, in: Proceedings of the 19th International Deep Drawing Research Group Congress, Eger, June 10-14, 1996.
16. A. Makinouchi, E. Nakamachi, E. Onate, R.H. Wagoner (Eds.), Proceedings of the Second International Conference on Numerical Simulation of 3-D Sheet Metal Forming Processes-Verification of Simulation with Experiments (Numisheet'2002), Isehara, Japan, 31 August-2 September, 2002.
17. M. Burlat, Analyse Mécanique et Tribologique de l'emboutissage: application aux outils fabriqués par combinaison de différents matériaux, Ph.D. Thesis, Institut National des Sciences Appliquées de Lyon, 1998.
18. Quantech ATZ, Stampack user guide-version 5.6, Quantech edition, Edificio Nexus, Gran Capitán, 2-4, 08034, Barcelona, Spain, 2004.
19. CATIA V5 R14 (2005) user guide, documents online.
20. Yoneno M., Sawa T., and Ishihara T. The strength of joints combining adhesives with blolts (case where adherends are pipe flanges of which the interfaces are bonded partially). JSME Int. J. Series A 42 N1 (1999) 126-134