Scratch test induced shear banding in high power laser remelted metallic glass layers

Journal of Materials Research

Volumn 22, Issue 2, 2007, Pages 460-470

  Mathews, D T A ^a   Ocelik V ^a   de Hosson, J Th M ^a  

^a UNIVERSITY OF GRONINGEN   (Netherlands)

Author keywords

[No Author keywords available]

Indexed keywords

COPPER ALLOYS; CORRELATION METHODS; HIGH POWER LASERS; INDENTATION; SHEAR BANDS; STRAIN RATE; STRESS CONCENTRATION; SURFACE ROUGHNESS; VICKERS HARDNESS;

FRICTION COEFFICIENT; LASER REMELTED SURFACE LAYERS; SCRATCH TESTING;

METALLIC GLASS;

EID: 33947203659     PISSN: 08842914     EISSN: None     Source Type: Journal    
DOI: 10.1557/jmr.2007.0056     Document Type: Article

References (13)

1. C.A. Schuh and T.G. Nieh: A nanoindentation study of serrated flow in bulk metallic glasses. Acta Mater. 51, 87 (2003).
2. S. Jana, U. Ramamurty, K. Chattopadhyay, and Y. Kawamura: Subsurface deformation during Vickers indentation of bulk metallic glasses. Mater. Sci. Eng., A 375-377, 1191 (2004).
3. A.V. Sergueeva, N.A. Mara, J.D. Kuntz, E.J. Laernia, and A.K. Mukherjee: Shear band formation and ductility in bulk metallic glass. Philos. Mag. 85, 2671 (2005).
4. B. Yang, L. Riester, and T.G. Nieh: Strain hardening and recovery in a bulk metallic glass under nanoindentation. Scripta Mater. 54, 1277 (2006).
5. D.T.A. Matthews, V. Ocelik and J.Th.M. de Hosson: Metallic glass layers produced by high power lasers, in Bulk Metallic Glass. Special Issue, Mater. Sci. Eng. A (in press).
6. E.S. Park, H.K. Lim, W.T. Kim, and D.H. Kim: The effect of Sn addition on the glass-forming ability of Cu-Ti-Zr-Ni-Si metallic glass alloys. J. Non-Cryst. Solids 298, 15 (2002).
7. S.J. Bull and D.S. Rickerby: Multi-pass scratch testing as a model for abrasive wear. Thin Solid Films 181, 545 (1989).
8. B.N.J. Persson: Sliding friction. Surf. Sci. Rep. 33, 83 (1999).
9. S. Bennett, A. Matthews, A.J. Perry, J. Valli, S.J. Bull, and W.D. Sproul: Multi-pass scratch testing at sub-critical loads. Tribologia. Finnish J. Tribol. 13, 16 (1994).
10. M. Pilloz, J.M. Pelletier, and A.B. Vannes: Residual stresses induced by laser coatings: Phenomenological analysis and predictions. J. Mater. Sci. 27, 1240 (1992).
11. Third Generation Hard X-ray Synchrotron Radiation Sources: Source Properties, Optics, and Experimental Techniques, edited by D.M. Mills (Wiley, USA, 2002).
12. Y. Zhao, C.C. Wang, and T.M. Lu, Characterization of Amorphous and Crystalline Rough Surface: Principles and Applications (Academic Press, Elsevier, USA, 2001).
13. F. Spaepen: A microscopic mechanism for steady state inhomogeneous flow in metallic glasses. Acta Metall. 25, 407 (1977).