Residual stress analysis of orthotropic materials by the through-hole drilling method

Experimental Mechanics

Volumn 47, Issue 2, 2007, Pages 217-236

  Pagliaro, P ^a   Zuccarello, B ^a  

^a UNIVERSITY OF PALERMO   (Italy)

Author keywords

Composite materials; Hole drilling method; Orthotropic materials; Residual stress

Indexed keywords

ORTHOTROPIC MATERIALS; THROUGH-HOLE DRILLING METHOD;

COMPUTER SIMULATION; LAMINATED COMPOSITES; RESIDUAL STRESSES; STRAIN;

DRILLING;

COMPUTER SIMULATION; DRILLING; LAMINATED COMPOSITES; RESIDUAL STRESSES; STRAIN;

EID: 33847651024     PISSN: 00144851     EISSN: 17412765     Source Type: Journal    
DOI: 10.1007/s11340-006-9019-3     Document Type: Article

References (30)

1. Mathar J (1934) Determination of initial stresses by measuring the deformation around drilled holes. Trans ASME 56:249-254.
2. Soete W (1949) Measurement and relaxation of residual stress. Sheet Met Ind 26(266):1269-1281.
3. Rendler NJ, Vigness I (1966) Hole-drilling strain-gage method of measuring residual stresses. Exp Mech 6(12):577-586.
4. Schajer GS (1981) Application of finite element calculations to residual stress measurements. J Eng Mater Technol 103(2):157-163.
5. Schajer GS (1988) Measurement of non-uniform residual stress using the hole-drilling method. Part I - stress calculation procedures. J Eng Mater Technol 110(4):338-343.
6. Schajer GS (1988) Measurement of non-uniform residual stress using the hole-drilling method. Part II - practical application of the integral method. J Eng Mater Technol 110(4):344-349.
7. Zuccarello B (1999) Optimal calculation steps for the evaluation of residual stress by the incremental hole-drilling method. Exp Mech 39(2):117-124.
8. ASTM E 837-01 (2001) Standard test method for determining residual stresses by the hole-drilling strain gauge method. Annual book of ASTM standards, American Society for Testing and Materials, Philadelphia.
9. Petrucci G, Zuccarello B (1998) A new calculation procedures for non-uniform residual stress analysis by the hole drilling method. J Strain Anal 33(1):27-37.
10. Bert CW, Thompson GL (1968) A method for measuring planar residual stresses in rectangularly orthotropic materials. J Compos Mater 2(2):244-253.
11. Lake BR, Appl FJ, Bert CW (1970) An investigation of the hole-drilling technique for measuring planar residual stress in rectangularly orthotropic materials. Exp Mech 10(10):233-239.
12. Prasad CB, Prabhakaran R, Thompkins S (1987) Determination of calibration constants for hole-drilling residual stress measurement technique applied to orthotropic composites. Composite structures, Part I: TheoretiEal considerations 8(2):105-118; Part II: experimental evaluations 8(3):165-172.
13. Sicot O, Gong XL, Cherouat A, Lu J (2003) Determination of residual stress in composite laminates using the incremental hole-drilling method. J Compos Mater 37(9):831-844.
14. Sicot O, Gong XL, Cherouat A, Lu J (2004) Influence of experimental parameters on determination of residual stress in composite laminates using the incremental hole-drilling method. Compos Sci Technol 64:171-180.
15. Schajer GS, Yang L (1994) Residual-stress measurement in orthotropic materials using the hole-drilling method. Exp Mech 34(4):324-333.
16. Càrdenas-Garìa JF, Ekwaro-Osire S, Berg JM, Wilson WH (2005) Non-linear last-squares solution to the moiré hole method problem in orthotropic materials. Part I: Residual stresses. Exp Mech 45(4):301-313.
17. Lekhnitskii SG (1968) Anisotropic plates. Gordon and Breach, New York.
18. Savin GN (1961) Stress concentration around holes. In: Johnson W (ed). Pergamon, New York (translated by Mr. E. Gros for the Department of Science and Industrial Research).
19. Tan SC (1994) Stress concentration in laminates composites. Technomic, Lancaster, PA.
20. Pagliaro P (2004) Analisi delle tensioni residue in laminati compositi mediante il metodo del foro. Tesi di Laurea, Facoltà di Ingegneria, Università degli Studi di Palermo.
21. Pagliaro P, Zuccarello B (2004) Analisi delle tensioni residue in laminati compositi mediante il metodo del foro. Atti del XXXII Convegno Nazionale AIAS, Bari.
22. Muskhelishvili NI (1953) Some basic problems in the mathematical theory of elasticity. Noordhoff, Groningen, Holland.
23. Maksimenko VN, Podruzhin EG (2005) Singular solution for an anisotropic plate with an elliptical hole. J Appl Mech Tech Phys 46(1):117-123.
24. Barbero EJ (1998) Introduction to composite materials design. Taylor & Francis, Philadelphia
25. Kabiri M (1986) Toward more accurate residual-stress measurement by the hole-drilling method: Analysis of relieved-strain coefficients. Exp Mech 26(1):14-21.
26. Ajovalasit A (1989) Experimental stress analysis of residual stresses: comparison of hole drilling, core and ring methods. OIAZ 418-420.
27. Schajer GS (1993) Use of displacement data to calculate strain gauge response in non-uniform strain fields. Strain 29(1):9-13.
28. Ajovalasit A, Zuccarello B (2005) Local reinforcement effect of a strain gauge installation on low modulus materials. J Strain Anal 40(7):643-654.
29. ASTM D-3039-93 (1993) Standard test method for tensile properties of polymeric matrix composite materials. Annual book of ASTM standards, American Society for Testing and Materials, Philadelphia.
30. ASTM D-4255-83 (1983) Standard guide for testing inplane shear properties of composites laminates. Annual book of ASTM standards, American Society for Testing and Materials, Philadelphia.