Sensitivity analysis of full field methods for residual stress measurement

Optics and Lasers in Engineering

Volumn 45, Issue 5, 2007, Pages 651-660

  Baldi, Antonio ^a   Bertolino, Filippo ^a  

^a UNIVERSITY OF CAGLIARI   (Italy)

Author keywords

Hole drilling; Noise sensitivity; Residual stress

Indexed keywords

COMPUTER SIMULATION; MONTE CARLO METHODS; OPTICAL PROPERTIES; ROBUSTNESS (CONTROL SYSTEMS); SENSITIVITY ANALYSIS; STRESS ANALYSIS;

HOLE DRILLING; NOISE SENSITIVITY; OPTICAL TECHNIQUES;

RESIDUAL STRESSES;

EID: 33847049854     PISSN: 01438166     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.optlaseng.2006.08.010     Document Type: Article

References (20)

1. A.S. for Testing and Materials, Standard test method for determining residual stresses by the hole-drilling strain-gage method (e837-01e1). In: Annual book of ASTM standards, vol. 03-01, West Conshohocken, PA: ASTM, 2003.
2. Rowlands R.E. Residual stresses. In: Kobayashi A.S. (Ed). Handbook on experimental mechanics (1987), Prenctice-Hall, Englewood Cliffs, NJ 768-813 [Chapter 18]
3. Lu J, editor. Handbook of measurement of residual stresses. Society for Experimental Mechanics, Inc., The Fairmont Press, Inc., 1996.
4. Bray DE, editor. Residual stress measurement and general nondestructive evaluation. vol. PVP 429, American Society of Mechanical Engineering, Pressure Vessels and Piping Division, 2001.
5. Kandil FA, Lord JD, Fry AT, Grant PV. Review of residual stress measurement methods-a guide to technique selection. Technical Report MATC(A)04. National Physical Laboratory, 〈http://www.npl.co.uk/materials/residualstress/npl_publications.html〉, project CPM4.5, Measurement of Residual Stress in Components (2001).
6. Schajer G.S. Measurement of non-uniform residual stresses using the hole-drilling method. Part i-stress calculation procedures. J Eng Mater Technol 110 4 (1988) 338-343
7. Schajer G.S. Measurement of non-uniform residual stresses using the hole-drilling method. Part ii-practical application of the integral method. J Eng Mater Technol 110 4 (1988) 344-349
8. Ajovalasit A. Measurement of residual stresses by the hole-drilling method: influence of hole eccentricity. J Strain Anal 14 (1979) 171-178
9. Wu Z., and Lu J. Study of surface residual stress by three-dimensional displacement data at a single point in hole drilling method. J Eng Mater Technol 122 2 (2000) 215-220
10. Nelson D.V., Makino A.M., and Fuchs E.A. The holographic-hole drilling method for residual stress determination. Opt Lasers Eng 27 (1997) 3-23
11. Focht G., and Schiffner K. Numerical processing of measured full-field displacement data around holes for residual stress determination. In: Mang H.A., Rammerstorfer F.G., and Eberhrdsteiner J. (Eds). Fifth world congress on computational mechanics (2002), Vienna, Austria
12. Baldi A. A new analytical approach for hole drilling residual stress analysis by full field method. J Eng Mater Technol 127 2 (2005) 165-169
13. Pisarev V.S., Balalov V.V., and Bondarenko M.M. Classification of holographic fringe patterns inherent in through hole drilling in residual stress field. Opt Lasers Eng 42 6 (2004) 673-702
14. Pisarev V.S., Balalov V.V., Chumak S.V., and Grigoriev V.D. Residual stresses deriving from holographic interferometry data on a base of inverse problem solution. Opt Lasers Eng 42 6 (2004) 703-726
15. Pisarev V.S., Bondarenkov M.M., Chernov A.V., and Vinogradova A.N. General approach to residual stresses determination in thin-walled structures by combining the hole drilling method and reflection. Int J Mech Sci 47 9 (2005) 1350-1376
16. Pisarev V.S., Apalkov A.A., Odintsev I.N., and Bondarenkov M.M. Determination of membrane and bending residual stress components in thin-walled plane structures. J Holography and Speckle 2 2 (2005) 57-71
17. Viotti M.R., Albertazzi A.J., and Kaufmann G.H. Residual stress measurement using a radial in-plane speckle interferometer and laser annealing: preliminary results. Opt Lasers Eng 42 1 (2004) 71-84
18. Nelson D.V., and McCrickerd J.T. Residual-stress determination through combined use of holographic interferometry and blind hole drilling. Exp Mech 26 (1986) 371-378
19. Wu Z., Lu J., and Han B. Study of residual stress distribution by a combined method of moiré interferometry and incremental hole drilling, part i: theory. J Appl Mech 65 4 (1998) 837-843
20. Press W.H., Teukolsky S.A., Vetterling W.T., and Flannery B.P. Numerical recipes in C. The art of scientific computing. 2nd ed. (1992), Cambridge University Press, Cambridge