Constrained sintering of YSZ/Al2O3 composite coatings on metal substrates produced from eletrophoretic deposition

Journal of the European Ceramic Society

Volumn 27, Issue 7, 2007, Pages 2613-2621

  Lu, X J ^a   Xiao, P ^a  

^a UNIVERSITY OF MANCHESTER   (United Kingdom)

Author keywords

Al2O3; Hot pressing; Porosity; Sintering; YSZ

Indexed keywords

CHARACTERIZATION; DEPOSITION; ELECTRON MICROSCOPY; INDENTATION; METALS; MICROSCOPIC EXAMINATION; MICROSTRUCTURE; RESIDUAL STRESSES; SINTERING; SUBSTRATES;

COMPOSITE COATINGS; CONSTRAINED SINTERING; ELECTROPHORETIC DEPOSITION; METAL SUBSTRATES;

ELECTROPHORETIC COATINGS;

CHARACTERIZATION; DEPOSITION; ELECTRON MICROSCOPY; ELECTROPHORETIC COATINGS; INDENTATION; METALS; MICROSCOPIC EXAMINATION; MICROSTRUCTURE; RESIDUAL STRESSES; SINTERING; SUBSTRATES;

EID: 33846682711     PISSN: 09552219     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.jeurceramsoc.2006.09.016     Document Type: Article

References (45)

1. Miller R.A. Current status of thermal barrier coatings-an overview. Surf. Coat. Technol. 30 (1987) 1
2. Evans A.G., Mumm D.R., Hutchinson J.W., Meier G.H., and Pettit F.S. Mechanisms controlling the durability of thermal barrier coatings. Prog. Mater. Sci. 46 (2001) 505
3. Schlichting K.W., Padture N.P., Jordan E.H., and Gell M. Failure modes in plasma-sprayed thermal barrier coatings. Mater. Sci. Eng. A 342 (2003) 120
4. Jones R.L. Metallurgical and Ceramic Coatings (1996), Chapman & Hall, London p. 194
5. Padture N.P., Gell M., and Jordan E.H. Thermal barrier coatings for gas-turbine engine applications. Science 296 (2002) 280
6. Wang Z., Shemilt J., and Xiao P. Fabrication of ceramic composite coatings using electrophoretic deposition, reaction bonding and low temperature sintering. J. Eur. Ceram. Soc. 22 (2002) 183
7. Ma J., Wang C., and Peng K.W. Electrophoretic deposition of porous hydroxyapatite scaffold. Biomaterials 24 (2003) 3505
8. Mcpherson R. A Review of microstructure and properties of plasma sprayed ceramic coating. Surf. Coat. Technol. 39/40 (1989) 173
9. Cernuschi F., Lorenzoni L., Ahmaniemi S., Vuoristo P., and Mantyla T. Studies of the sintering kinetic of thick thermal barrier coatings by thermal diffusivity measurements. J. Eur. Ceram. Soc. 25 (2005) 393
10. Guo S., and Kagawa Y. Effect of thermal exposure on hardness and Young's modulus of EB-PVD yttria-partially-stabilized zirconia thermal barrier coatings. Ceram. Int. 32 (2006) 263
11. Thompson J.A., and Clyne T.W. The effect of heat treatment on the stiffness of Zirconia top coats in plasma-sprayed TBCs. Acta Mater. 49 (2001) 1565
12. Renteria A.F., and Saruhan B. Effect of ageing on microstructure changes in EB-PVD manufactured standard YSZ top coat of thermal barrier coatings. J. Eur. Ceram. Soc. 26 (2006) 2249
13. Bordia R.K., and Raj R. Sintering behavior of ceramic films constrained by a rigid substrate. J. Am. Ceram. Soc. 68 (1985) 287
14. Bang J., and Lu G.-Q. Constained-film sintering of a borosilicate glass: in situ measurement of film stresses. J. Am. Ceram. Soc. 78 (1995) 813
15. Choe J.W., Calata J.N., and Lu G.-Q. Constrained-film sintering of a gold circuit paste. J. Mater. Res. 10 (1995) 986
16. Bordia R.K., and Jagota A. Crack growth and damage in constrained sintering films. J. Am. Ceram. Soc. 76 (1993) 2475
17. Garino T.J., and Bowen H.K. Kinetics of constrained-film sintering. J. Am. Ceram. Soc. 73 (1990) 251
18. Tzeng S.-Y., and Jean J.-H. Stress development during constrained sintering of alumina/glass/alumina sandwich structure. J. Am. Ceram. Soc. 85 (2002) 335
19. Lin Y.-C., and Jean J.-H. Constrained densification kinetics of alumina/borosilicate glass + alumina/alumina sandwich structure. J. Am. Ceram. Soc. 85 (2002) 150
20. Cheng T., and Raj R. Flaw generation during constrained sintering of metal-ceramic and metal-glass multilayer films. J. Am. Ceram. Soc. 72 (1989) 1649
21. Calata J.N., Matthys A., and Lu G.-Q. Constrained-film sintering of Cordierite glass-ceramic on silicon substrate. J. Mater. Res. 13 (1998) 2334
22. Oliver W.C., and Pharr G.M. An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments. J. Mater. Res. 7 (1992) 1564
23. 3 composite coatings. Acta Mater. 52 (2004) 2591
24. Lu X.-J., Wang X., and Xiao P. Nanoindentation and residual stress measurements of yttria-stablized zirconia composite coatings produced by electrophoretic deposition. Thin Solid Films 494 (2005) 223
25. Sergo V., Wang X.L., Clarke D.R., and Becher P.F. Residual stresses in alumina/ceria-stabilized zirconia composites. J. Am. Ceram. Soc. 78 (1995) 2213
26. Tolpygo V.K., and Clarke D.R. Wrinkling of alumina films grown by thermal oxidation. I. Quantitative studies on single crystals of Fe-Cr-Al alloy. Acta Mater. 46 (1998) 5153
27. Shackelford J.F., and Alexander W. CRC Materials Science and Engineering Handbook (2001), CRC Press, New York p. 766
28. Green D.J. An Introduction to the Mechanical Properties of Ceramics (1998), Cambridge University Press, Cambridge p. 25
29. Raj R. Analysis of the sintering pressure. J. Am. Ceram. Soc. 70 (1987) C210
30. Shi J.L. Relation between coarsening and densification in solid-state sintering of ceramics. J. Mater. Res. 14 (1999) 1389
31. Shi J.L. Thermodynamics and densification kinetics in solid-state sintering of ceramics. J. Mater. Res. 14 (1999) 1398
32. Chen I.-W., and Wang X.-H. Sintering dense nanocrystalline ceramics without final-stage grain growth. Nature 404 (2000) 168
33. Tsoga A., and Nikolopoulos P. Surface and grain-boundary energies in yttria-stabilized zirconia. J. Mater. Sci. 31 (1996) 5409
34. Reed J.S. Principles of Ceramics Processing. 2nd ed. (1995), John Wiley& Sons Inc., New York p. 617
35. Zuo R., Aulbach E., Bordia R.K., and Rodel J. Critical evaluation of hot forging experiments: case study in alumina. J. Am. Ceram. Soc. 86 (2003) 1099
36. Svoboda J., Riedel H., and Zipse H. Equilibrium pore surfaces, sintering stresses and constitutive equations for the intermediate and late stages of sintering. I. Computation of equilibrium surfaces. Acta Metall. Mater. 42 (1994) 435
37. Kanters H., Eisele U., and Rodel J. Cosintering simulation and experimentation: case study of nanocrystalline zirconia. J. Am. Ceram. Soc. 84 (2001) 2757
38. Bordia R.K., Zuo R., Guillon O., Salamone S.M., and Rodel J. Anisotropic constitutive laws for sintering bodies. Acta Mater. 54 (2006) 111
39. Aahmy A.A., and Ragai A.N. Thermal-expansion behavior of two-phase solids. J. Appl. Phys. 41 (1970) 5108
40. Liu D.-M., and Winn E.J. Microstresses in particulate-reinforced brittle composites. J. Mater. Sci. 36 (2001) 3487
41. Spriggs R.M. Expression for effect of porosity on elastic modulus of polycrystalline refractory materials, particularly aluminum oxide. J. Am. Ceram. Soc. 44 (1961) 628
42. Knudsen F.P. Dependence of mechanical strength in brittle polycrystalline specimens on porosity and grain size. J. Am. Ceram. Soc. 42 (1959) 376
43. Mccolm I.J. Ceramic Hardness (1990), Plenum Press, New York p. 276
44. Kingery W.D. Introduction to Ceramics (1975), John Wiley & Sons Inc. p. 595
45. Mccolm I.J. Ceramic Hardness (1990), Plenum Press, New York p. 8