The influence of operating and design parameters on the magnetic tape/guide friction coefficient

Tribology Letters

Volumn 25, Issue 2, 2007, Pages 161-171

  Raeymaekers, Bart ^a   Etsion, Izhak ^b   Talke, Frank E ^a  

^a UNIVERSITY OF CALIFORNIA   (United States)

^b TECHNION ISRAEL INSTITUTE OF TECHNOLOGY   (Israel)

Author keywords

Belt drive friction; Friction modeling; Magnetic tape tribology

Indexed keywords

BELT DRIVE EQUATION; FRICTION COEFFICIENT; SLIDING SPEED; TAPE GEOMETRY;

BELT DRIVES; FRICTION; SURFACE ROUGHNESS;

MAGNETIC TAPE;

BELT DRIVES; FRICTION; MAGNETIC TAPE; SURFACE ROUGHNESS;

EID: 33846516358     PISSN: 10238883     EISSN: None     Source Type: Journal    
DOI: 10.1007/s11249-006-9165-x     Document Type: Article

References (26)

1. Shigley J.E., Mischke C.R. (1989) Mechanical Engineering Design. McGraw Hill, New York
2. Etsion I., Levinson O., Halperin G., Varenberg M. (2005) J. Tribol. T. ASME 127:47
3. Broese van Groenou A. (1990) IEEE T. Magn. 26(1):144
4. Osaki H. (2000) Tribol. Int. 33:377
5. Osaki H., Endo T. (2005) Tribol. Int. 38:616
6. Panda S.P., Engelmann A.P. (2003) J. Micr. Tech. 10:53
7. Taylor R., Talke F.E. (2005) Tribol. Int. 38:599
8. Bhushan B. (1984) Wear 93:81
9. Lacey C., Talke F.E. (1992) J. Tribol. T. ASME 114:646
10. Patir N., Cheng H.S. (1978) J. Lubr. Technol. T. ASME 100(1):12
11. Chang W.R. Etsion I. Bogy D.B. (1988) J. Tribol. T. ASME 110 (1): 57
12. Tworzydlo W.W., Cecot W., Oden J.T., Yew C.H. (1998) Wear 220 (1): 113
13. Amassad A., Shillor M., Sofonea M. (1999) Nonlinear Anal. Theor. 35:95
14. Alexandrov S., Richmond O., (2001) Int. J. Mech. Sci. 43:653
15. Kogut L., Etsion I. (2004) J. Tribol. T. ASME 126:34
16. V. Brizmer, Y. Kligerman and I. Etsion, Tribol. Lett. (2006) DOI 10.1007/ s11249-006-9156-y
17. Brizmer V., Kligerman Y., Etsion I. (2006) Int. J. Sol. Str. 43:5736
18. Rabinowicz E., (1965) Friction and Wear of Materials (J. Wiley and sons, New York
19. J.A. Greenwood and J.B.P. Williamson, Proc. Roy. Soc. Lond. Ser. A - Math. Phys. Sci. 295(1442) (1966) 300
20. Greenwood J.A., Tripp J.H. (1967) J. Appl. Mech. T. ASME 34(1):153
21. Kogut L., and Etsion I. (2003) Tribol. Trans. 46:383
22. Lacey C., Talke F.E. (1990) IEEE T. Magn. 26(4):3039
23. McCool J.I. (1987) J. Tribol. T. ASME 109:264
24. Hempstock M.S., Sullivan J.L. (1996) IEEE T. Magn. 32(3):3723
25. Hempstock M.S., Sullivan J.L. (1996) J. Mag. Mag. Mat. 155:323
26. Bijker M.D., Draaisma E.A., Eisenberg M., Jansen J., Persat N., Sourty E. (2000) Tribol. Int. 33:383