An experimental study of the enhancement of air-cooling limits for telecom/datacom heat sink applications using an impinging air jet

Journal of Electronic Packaging

Volumn 128, Issue 2, 2006, Pages 166-171

  Sansoucy, Eric ^a,b   Oosthuizen, Patrick H ^a,c   Refai Ahmed, Gamal ^d  

^a ASME   (Canada)

^b UNIVERSITY OF OTTAWA   (Canada)

^c QUEEN S UNIVERSITY   (Canada)

^d ADVANCED MICRO DEVICES   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

COMPUTER SIMULATION; COOLING SYSTEMS; HEAT TRANSFER; JETS; NOZZLES; NUSSELT NUMBER; TURBULENT FLOW;

AIR COOLING LIMITS; IMPINGEMENT ARRANGEMENT; IMPINGING AIR JET; NOZZLE PLATE;

HEAT SINKS;

EID: 33845717674     PISSN: 10437398     EISSN: None     Source Type: Journal    
DOI: 10.1115/1.2164848     Document Type: Article

References (12)

1. Martin, H., 1977, "Heat and Mass Transfer between Impinging Gas Jets and Solid Surfaces," Adv. Heat Transfer, 13, pp. 1-60.
2. Hrycak, P., 1984, "Heat Transfer from Impinging Jets to a Flat Plate With Conical and Ring Protuberances," Int. J. Heat Mass Transfer, 27, pp. 2145-2154.
3. Hansen, L. G., and Wcbb, B. W., 1993, "Air Jet Impingement Heat Transfer from Modified Surfaces," Int. J. Heat Mass Transfer, 36, pp. 989-997.
4. Brignoni, L". A., and Garimella, S. V., 1999, "Experimental Optimization of Confined Air Jet Impingement on a Pin Fin Heat Sink," IEEE Trans. Compon. Packag. Technol., 22, pp. 399-404.
5. El-Sheikh, H. A., and Garimella, S. V., 2000, "Enhancement of Air Jet Impingement Heat Transfer Using Pin-Fin Heat Sinks," IEEE Trans. Compon. Packag. Technol., 23, pp. 300-308.
6. Issa, J. S., and Ortega, A., 2002, "Experimental Measurements of the Flow and Heat Transfer of a Square Jet Impinging on an Array of Square Pin Fin," Proc., ASME Heat Transfer Division, New Orleans, November 17-22, Vol. 2, pp. 179-193.
7. Jung, H. H., and Maveety, J. G., 2000, "Pin-Fin Heat Sink Modeling and Characterization," Proc., I6th IEEE Semiconductor Tliennal Measurement and Management (SEMI-THERM) Symposium, San Jose, CA, March 21-23, pp. 260-265.
8. Sansoucy, E., Oosthuizen, P. H., and Refai-Ahmed, G., 2003, "Enhancement of Air-Cooling Limits for Telecom Heat Sink Applications Using Impinging Air Jets," Proc., ASME Heat Transfer Division, Washington, DC, November 15-21, Vol. 2, pp. 307-315.
9. Sansoucy, E., 2003, "Experimental and Numerical Investigation of the Effects of an Impinging Air Jet on the Heat Transfer Rate from a Parallel Flat Plate Heat Sink," M.S. thesis, Department of Mechanical Engineering, Queen's University.
10. Kraus, A. D., and Bar-Cohen, A., 1983, Therml Analysis and Control of Electronic Equipment, 1st ed., McGraw-Hill Book Company, New York.
11. Craft, T. J., Graham, L. J. W., and Launder, B. E., 1993, "Impinging Jet Studies for Turbulence Model Assessment - II: An Examination of the Performance of Four Turbulence Model," Int. J. Heat Mass Transfer, 36, pp. 2685-2697.
12. Polat, S., Huang, B., Mujumbar, A. S., and Douglas, W. J. M., 1989, "Numerical Flow and Heat Transfer Under Impinging Jets: A Review," Drying Technol., 3, pp. 15-38.