Visualization analysis of the filling behavior of melt into microscale V-grooves during the filling stage of injection molding

Polymer Engineering and Science

Volumn 46, Issue 11, 2006, Pages 1590-1597

  Han, X ^a   Yokoi, H ^b  

^a INSTITUTE OF INDUSTRIAL SCIENCE   (Japan)

^b UNIVERSITY OF TOKYO   (Japan)

Author keywords

[No Author keywords available]

Indexed keywords

GLASS; INJECTION MOLDING; PRISMS; VISUALIZATION;

CAVITY THICKNESS; FILLING BEHAVIOR; FILLING RATIO; INJECTION RATE;

POLYMERS;

EID: 33751369474     PISSN: 00323888     EISSN: 15482634     Source Type: Journal    
DOI: 10.1002/pen.20615     Document Type: Article

References (16)

1. D.G. Yao and B. Kim, Polym. Eng. Sci., 42, 2471 (2002).
2. H. Kataoka, Y. Umei, and I. Kato, Seikei Kako, 9, 889 (1997).
3. K. Inoue, K. Hayashi, Y. Kawasaki, and E. Ohno, Jpn. J. Appl. Phys., 42, Part 1 (2B) 774 (2003).
4. S. Murata, Y. Itoh, and H. Itoh, Ricoh Tech. Rep., 27(11), 77 (2001).
5. K. Yasuda, Plastics, 52, 96 (2001).
6. Y. Umino, K. Ohba, and H. Tateyama, "Effect of Carbon Dioxide on Surface Minute Transcription," Seikei-Kakou '04, 97 (2004).
7. Y. Kurosaki and K. Sato, "A Novel Polymer Processing Assisted by Infrared Radiation to Attain a High Precision Transcription," SPE ANTEC'00, 156 (2000).
8. K. Sato, Y. Kurosaki, and T. Saito, Seikei Kako, 13, 751 (2001).
9. H. Yokoi, T. Takahashi, W. K. Kim, and A. Segawa, "High- Transcription-Ratio Molding Based on Ultra-High-Speed Injection Molding Technology," JSPE Autumn Conference'02, 185 (2002).
10. X. Han, H. Yokoi, T. Takahashi, and W. K. Kim, "Transcription Molding of Micro-Scale Patterns Using Ultra-High-Speed Injection Molding," PPS-19, Melbourne, Australia, (2003). CD-ROM No. 401.
11. X. Han, H. Yokoi, and T. Takahashi, "Effects of Groove-Layout and Molding Conditions on Transcription Molding of Micro-Scale Patterns Using Ultra-High-Speed Injection Molding Technology," PPS-2004 Asia/Australia Meeting, Gyeongju, Korea, (2004). CD-ROM No. 30-O-G2-08.
12. M. Yoshii, H. Kuramoto, and K. Kato, Polym. Eng. Sci., 34, 1211 (1994).
13. M.S. Despa, K.W. Kelly, and J.R. Collier, Microsyst. Technol., 6, 60 (1999).
14. Y. Ono, C.-K. Jen, C.-C. Cheng, and M. Kobayashi, Polym. Eng. Sci., 45, 606 (2005).
15. H. Yokoi, J. JSEME, 33, 1 (1999).
16. H. Yokoi, T. Hayashi, K. Toda, and N. Morikita, "Direct Observation of Jetting Phenomena Under a High Injection Pressure by Using a Prismatic Glass Inserted Mold," SPE ANTEC'88, 329 (1988).