The Risk in Early Design (RED) method: Likelihood and consequence formulations

Proceedings of the ASME Design Engineering Technical Conference

Volumn 2006, Issue , 2006, Pages

  Lough, Katie Grantham ^a   Stone, Robert B ^a   Tumer, Irem ^b  

^a Architectural and Environmental Engineering   (United States)

^b NASA AMES RESEARCH CENTER   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

FUNCTIONS; MAXIMUM LIKELIHOOD ESTIMATION; RISK ASSESSMENT; SPACECRAFT;

FAILURE MODE; RISK ELEMENTS; SPACECRAFT ORIENTATION SUBSYSTEM;

STRUCTURAL DESIGN;

EID: 33751339270     PISSN: None     EISSN: None     Source Type: Conference Proceeding    
DOI: None     Document Type: Conference Paper

References (30)

1. Turner, I., Stone, R., "Mapping Function to Failure Mode During Component Development," Research in Engineering Design 14(1): 25-33, 2001.
2. Stone, R., Turner, I., Van Wie, M., "The Function Failure Design Method,", Journal of Mechanical Design [in press].
3. Grantham Lough, K., Stone, R., and Turner, I., "Function Based Risk Assessment: Mapping Function to Likelihood", Proceedings of 2005 ASME International Design Engineering Technical Conference, September 24-28, Long Beach, CA.
4. Grantham Lough, K., Stone, R., and Turner, I., "Prescribing and Implementing the Risk in Early Design (RED) Method", Proceedings of the ASME Design Engineering Technical Conference, Philadelphia, PA, 2006.
5. Gluch, David. A Construct for Describing Software Development Risks (CMU/SEI-94-TR-14). Pittsburgh, Pa.: Software Engineering Institute, Carnegie Mellon University, 1994.
6. th International Conference on Computer-Aided Industrial Design and Conceptual Design" Delft, The Netherlands, 2005.
7. Kaplan, S., and Garrick, J., "On the Quantitative Definition of Risk," Risk Analysis 1, 1(1981), pp 11-27.
8. Holloway, N.J."A method for pilot risk studies," In Implications of Probabilistic Risk Assessment, edited by M.C. Cullingford, S. M. Shah, and J. H. Gittus, pp. 125-140. New Your: Elsevier Applied Science, 1987.
9. Department of Defense, "Procedures for performing failure mode, effects, and criticality analysis." MIL-STD-1629A.
10. Lawley, H. G. "Operability studies and hazard analysis," Chemical Engineering Progress, vol. 70, no 4, pp. 45-56, 1974.
11. Vesely, W. E., Goldberg, F. F., Roberts, N. H. and Haasi, D. F., The Fault Tree Handbook, US Nuclear Regulatory Commission, NUREG 0492, 1981.
12. Frank, M.V., "Reentry safety: probability of fuel release", in Safety and Reliability, Proceedings of ESREL '99, eds G.I. Schneller and P. Kafka, Balkema, Rotterdam, 1999.
13. Bohnenblust, H. and T. Schneider. "Risk appraisal: Can it be improved by formal decision models?" In Uncertainty in Risk Assessment, Risk Management, and Decision Making.edited by V. T. Covello et al., pp. 71-87. New York Plenum Press, 1987.
14. Kurfman, M., Rajan, J., Stone, R., Wood, K. and Stock, M., 2003, "Experimental Studies Assessing the Repeatability of a Functional Modeling Derivation Method," Journal of Mechanical Design, 125(4):682-693.
15. Otto, K., and Wood, K., Product Design: Techniques in Reverse Engineering, Systematic Design, and New Product Development, New York, Prentice-Hall, 2001.
16. Hirtz, J., Stone, R., McAdams, D., Szykman, S., and Wood, K., "A Functional Basis for Engineering Design: Reconciling and Evolving Previous Efforts," Research in Engineering Design 13(2): 65-82, 2002.
17. Miles, L. (1972), Techniques of Value Analysis Engineering, McGraw-Hill.
18. Pahl, G. and W. Beitz (1984), Engineering Design: A Systematic Approach, Design Council, London.
19. Uder, S., Stone, R., and Turner, I., "Function Based Risk Assessment and Failure Prediction for Unmanned Space Missions," ASME International Mechanical Engineering Congress IMECE 2004-60846.
20. Turner, I., Stone, R., and Bell, D., "Requirements for a Failure Mode Taxonomy for use in Conceptual Design," Proceedings of the International Conference on Engineering Design, ICED, Stockholm, 2003, paper 1612.
21. Bohm, M., and Stone, R., "Product Design Support: Exploring a Design Repository System," ASME International Mechanical Engineering Congress IMECE 2004-61746.
22. Roberts, R., Stone, r., and Tumer, I., "Deriving Function-Failure Information for Failure-Free Rotorcraft Component Design," Proceedings of ASME Design Engineering Technical Conference, DETC2002/DFM-34166, Montreal, Canada, 2002.
23. Office of the Under Secretary of Defense, 1999, DSMC Risk Management Guide for DoD Acquisition, 2nd Edition, Defense Systems Management College Press, Fort Belvoir, Virginia.
24. Warren, J. A., Personal Communication, April 14, 2005, The Boeing Company, St. Louis, MO.
25. Greenfield, M., "Risk Management Tools," a presentation, Langley Research Center, May 2, 2000.
26. Lock, D., Handbook of Engineering Management, Oxford, Butterworth-Heinemann, 1993.
27. Wang, J., and Roush, M., What Every Engineer Should Know about Risk Engineering and Management, Marcel Dekker, Inc, New York, 2002.
28. ASM International, Handbook of Case Histories in Failure Analysis. vol. 1 (USA), 1992.
29. Fieseler, P. D., July 2003, The Galieleo Star Scanner as an Instrument for Measuring Energetic Electrons in the Jovian Environment.
30. Clarkson, P., Simmons, C., and Eckert, C., "Predicting Change Propagation in Complex Design," ASME Journal of Mechanical Design, 126(5), 788-797, 2004.