Prescribing and implementing the Risk in Early Design (RED) method

Proceedings of the ASME Design Engineering Technical Conference

Volumn 2006, Issue , 2006, Pages

  Lough, Katie Grantham ^a   Stone, Robert B ^a   Tumer, Irem ^b  

^a Architectural and Environmental Engineering   (United States)

^b NASA AMES RESEARCH CENTER   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

COMPUTER SIMULATION; HEURISTIC METHODS; MACHINE COMPONENTS; RISK ASSESSMENT;

FAILURE INFORMATION; RISK IN EARLY DESIGN (RED); THERMAL CONTROL SUBSYSTEMS;

PRODUCT DESIGN;

EID: 33751311302     PISSN: None     EISSN: None     Source Type: Conference Proceeding    
DOI: None     Document Type: Conference Paper

References (27)

1. Mark, G., "Extreme Collaboration," Communications of the ACM, 45(6): June 2002.
2. Meshkat, Cornford, S., and Moran, T., 2003, "Risk Based Decision Tool for Space Exploration Missions", American Institute of Aeronautics and Astronautics space Conference and Exhibition, AIAA 2003-6377.
3. Van Wie, M., Grantham Lough, K., Stone, R., Barrientos, F., and Turner, I., "An Analysis of Risk and Function Information in Early Stage Design", Proceedings of 2005 ASME International Design Engineering Technical Conference, September 24-28, Long Beach, CA.
4. th InternationalConference on Computer-Aided Industrial Design and Conceptual Design," Delft, The Netherlands, 2005.
5. Hirtz, J., Stone, R., McAdams, D., Szykman, S., and Wood, K., "A Functional Basis for Engineering Design: Reconciling and Evolving Previous Efforts," Research in Engineering Design 13(2): 65-82, 2002.
6. Tumer, I., Stone, R., and Bell, D., "Requirements for a Failure Mode Taxonomy for use in Conceptual Design," Proceedings of the International Conference on Engineering Design, ICED, Stockholm, 2003, paper 1612.
7. Stone, R., Turner, I., Van Wie, M., "The Function Failure Design Method,", Journal of Mechanical Design [in press]
8. Tumer, I., Stone, R., "Mapping Function to Failure Mode During Component Development," Research in Engineering Design 14(1): 25-33, 2001.
9. Uder, S., Stone, R., and Turner, I., "Function Based Risk Assessment and Failure Prediction for Unmanned Space Missions," ASME International Mechanical Engineering Congress IMECE 2004-60846.
10. Grantham Lough, K., Stone, R., and Turner, I., "Function Based Risk Assessment: Mapping Function to Likelihood", Proceedings of 2005 ASME International Design Engineering Technical Conference, September 24-28, Long Beach, CA.
11. Grantham Lough, K., Stone, R., and Turner, I., "The Risk in Early Design (RED) Method: Likelihood and Consequence Calculations", Submitted to Proceedings of 2006 ASME International Design Engineering Technical Conference.
12. Holloway, N.J."A method for pilot risk studies," In Implications of Probabilistic Risk Assessment, edited by M.C. Cullingford, S. M. Shah, and J. H. Gittus, pp. 125140. New Your: Elsevier Applied Science, 1987.
13. Department of Defense, "Procedures for performing failure mode, effects, and criticality analysis." MIL-STD-1629A.
14. Kumomoto, H. and Henley E., Probabilistic Risk Assessment and Management for Engineers and Scientists, New York, Institute of Electrical and Electronics Engineers, Inc., 1996.
15. Lawley, H. G. "Operability studies and hazard analysis," Chemical Engineering Progress, vol. 70, no 4, pp. 45-56, 1974.
16. Vesely, W. E., Goldberg, F. F., Roberts, N. H. and Haasi, D. F., The Fault Tree Handbook, US Nuclear Regulatory Commission, NUREG 0492, 1981.
17. Frank, M. V., "Reentry safety: probability of fuel release", in Safety and Reliability, Proceedings of ESREL '99, eds G.I. Schneller and P. Kafka, Balkema, Rotterdam, 1999.
18. Bohnenblust, H. and T. Schneider. "Risk appraisal: Can it be improved by formal decision models?" In Uncertainty in Risk Assessment, Risk Management, and Decision Making.edited by V. T. Covello et al., pp. 71-87. New York Plenum Press, 1987.
19. Kurfman, M., Rajan, J., Stone, R., Wood, K. and Stock, M., 2003, "Experimental Studies Assessing the Repeatability of a Functional Modeling Derivation Method," Journal of Mechanical Design, 125(4):682-693.
20. Otto, K., and Wood, K., Product Design: Techniques in Reverse Engineering, Systematic Design, and New Product Development, New York, Prentice-Hall, 2001.
21. Miles, L. (1972), Techniques of Value Analysis Engineering, McGraw-Hill.
22. Pahl, G. and W. Beitz (1984), Engineering Design: A Systematic Approach, Design Council, London.
23. Office of the Under Secretary of Defense, 1999, DSMC Risk Management Guide for DoD Acquisition, 2nd Edition, Defense Systems Management College Press, Fort Belvoir, Virginia.
24. Warren, J. A., Personal Communication, April 14, 2005, The Boeing Company, St. Louis, MO.
25. Brown, A. F. Development of a Method for Flight Anomaly Characterization. JPL Technical Report, JPL D-11382. 1994, Jet Propulsion Laboratory, California Institute of Technology, Pasadena, CA.
26. Quinn, J. D. Flight P/FRs and the Design Review Process. JPL Technical Report, JPL D-11381. 1994, Jet Propulsion Laboratory, California Institute of Technology, Pasedena, California.
27. Grantham Lough, K. A., "Risk in Early Design," A Dissertation, University of Missouri-Rolla, August 2005.