Effects of liner surface texturing on ring/liner friction in large-bore IC engines

American Society of Mechanical Engineers, Internal Combustion Engine Division (Publication) ICE

Volumn 2006, Issue , 2006, Pages

  Takata, Rosalind ^a   Li, Yong ^a   Wong, Victor W ^a  

^a MASSACHUSETTS INSTITUTE OF TECHNOLOGY   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

FRICTION; HYDRODYNAMICS; LUBRICANTS; REYNOLDS NUMBER; TEXTURES;

LINER SURFACES; RING SIMULATION; SURFACE PARAMETERS; SURFACE TEXTURING;

INTERNAL COMBUSTION ENGINES;

EID: 33751273384     PISSN: 10665048     EISSN: None     Source Type: Conference Proceeding    
DOI: 10.1115/ICEF2006-1525     Document Type: Conference Paper

References (16)

1. Hamilton, D.B., Walowit, J.A. and Allen, C.M., "A Theory of Lubrication by Microasperities", ASME J. Basic Eng., vol. 88, pp. 177-185, 1966.
2. Anno, J.N., Walowit, J.A. and Allen, C.M., "Microasperity Lubrication", ASME Journal of Lubrication Technology, vol. 90, pp. 351-355, 1968.
3. Anno, J.N., Walowit, J.A., and Allen, C.M., "Load Support and leakage from Microasperity-Lubricated Face Seals", ASME Journal of Lubrication Technology, vol. 91, pp. 726-731, 1969.
4. Kovalchenko, A., Ajayi, O., Erdemir, A., Fenske, G., Etsion, I., "The Effect of Laser Surface Texturing on Transitions in Lubrication Regimes During Unidirectional Sliding Contact", Tribology International, vol. 38, pp. 219-225, 2005.
5. Sadeghi, F., et. al., "Advanced Natural Gas Reciprocating Engine: Parasitic Loss Control Through Surface Modification," ARES/ARICE Low Engine Friction Alliance Workshop, Cambridge, MA, Dec. 1, 2005.
6. Ronen, A., Etsion, I., Kligerman, Y., "Friction-Reducing Surface-Texturing in Reciprocating Automotive Components," Tribology Transactions, vol. 44, pp. 359-366, 2001.
7. Ryk, G., Kligerman, Y., Etsion, I., "Experimental Investigation of Laser Surface Texturing for Reciprocating Automotive Components," Tribology Transactions, vol. 45, pp. 444-449, 2002.
8. Siripuram, R. and Stephens, L., "Effect of Deterministic Asperity Geometry on Hydrodynamic Lubrication", ASME Journal of Tribology, vol. 126, pp. 527-534, 2004.
9. Hsu, S., "Integrated Surface Modification Technology Development," presented Sept. 15, 2005.
10. Michail, S.K. and Barber, G.C., "The Effects of Roughness on Piston Ring Lubrication Part I: Model Development," Tribology Transactions, vol. 38, pp. 19-26, 1995.
11. Jocsak, J., et al., "Analyzing the Effects of Three-Dimensional Cylinder Liner Surface Texture." ICEF2005, Ottawa, Canada, #ICE2005-1333.
12. Tian, T., "Modeling and Performance of the Piston Ring-Pack in Internal Combustion Engines," PhD Thesis, Department of Mechanical Engineering, Massachusetts Institute of Technology, June 1997.
13. Greenwood, J.A., Tripp, J., "The Contact of Two Nominally Flat Surfaces," Proc. Inst. Mech. Engrs., vol. 185, pp. 625-633, 1971.
14. Hu, Y., et. al., "Numerical Simulation of Piston Ring in Mixed Lubrication - A Non-Axisymmetrical Analysis," ASME Journal of Tribology, 1993.
15. Jocsak, J. et al., "The Effects of Cylinder Liner Finish on Piston Ring-Pack Friction," ICEF2004, Long Beach, CA, #ICEF2004-952.
16. Patir, N. and Cheng, H., "Application of Average Flow Model to Lubrication Between Rough Sliding Surfaces," ASME Journal of Lubrication Technology, vol. 101, pp. 220-230, 1979.