Critical energy release rate for a CSM reinforced carbon fibre composite/steel bonding

Composites Part A: Applied Science and Manufacturing

Volumn 37, Issue 5, 2006, Pages 742-751

  Andresen, Håkon W ^a   Echtermeyer, Andreas T ^a,b  

^a NORWEGIAN UNIVERSITY OF SCIENCE AND TECHNOLOGY   (Norway)

^b DNV GL   (Norway)

Author keywords

B. Adhesion; B. Fracture toughness; Composite metal interface; D. Mechanical testing

Indexed keywords

ADHESION; BONDING; CARBON FIBERS; FRACTURE TOUGHNESS; MECHANICAL TESTING; STEEL; STIFFNESS;

ADHESIVE STRENGTH; COMPOSITE METAL INTERFACES; ENERGY RELEASE RATE; STEEL BONDING;

COMPOSITE MATERIALS;

EID: 33751183537     PISSN: 1359835X     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.compositesa.2005.06.009     Document Type: Article

References (32)

1. Chalkey P, Berg Jvd. On obtaining design allowables for adhesives used in the bonded-composite repair of aircraft. Airframes and engines division, aeronautical and maritime research laboratory, DSTO-TR-0608.
2. Baker A. Bonded composite repair of fatigue-cracked primary aircraft structure. Compos Struct 47 (1999) 431-443
3. Frost S., and Lee R. Composite overwraps for piping system and pressure vessel system repair. Oilfield engineering with polymers, London 3-4 November (2003)
4. Mableson A.R., Dunn K.R., Dodds N., and Gibson A.G. Refurbishment of steel tublar pipes using composite materials. Plast Rubber Compos 29 10 (2000) 558-565
5. Echtermeyer AT, Larsen MJ, Fischer KP. A new approach to the repair of FPSOs without hotwork. Proceedings of the 22nd internation conference on Offhore Mechanics and Arctic Engineering, OMAE Paper OMAE:2003-37426, Cancun, Mexico; 2003.
6. Europe fib bulletin 14. Externally bonded FRP reinforcement for RC structures. Federation internationale du Beton; 2001. ISSN 1562-3610.
7. ACI 440.2R-02. Guide for the design and construction of externally bonded FRP systems for strengthening concrete structures. American Concrete Institute; 2002.
8. deCharentenay F.X., Harry J.M., Prel Y.J., and Benzeggagh M.L. Characterizing the effect of delamination defect by mode I delamination test. ASTM STP 836 (1982) 84
9. Carlsson L.A., and Pipes R.B. Experimental characterization of advanced composite materials (1987), Prentice-Hall, Inc, Englewood Cliffs, NJ p.19-21, [see also p. 160-70]
10. Davis P., Cantwell W.J., and Kausch H.H. Delamination from thin starter films in carbon PEEK composites. J Mater Sci Lett 9 (1990) 1349-1350
11. Wilkins D.J., Eisenmann J.R., Camin R.A., Magrolis W.S., and Benson R.A. Characterizing delamination growth in Graphite-Epoxy. Damage Compos Mater ASTM STP 775 (1980) 168-183
12. Russell A.J., and Street K.N. Factors affecting the interlaminar fracture energy of graphite/epoxy laminates. Progress in science and engineering of composites, Tokyo (1982)
13. Echtermeyer AT, McGarry FJ, Mandell JF. Effect of damage on the stress concentration ahead of a notch in crossplied composites. PPST Report 89-2, Massachusetts institute of technology; 1989.
14. Rusell A.J., and Street K.N. Moisture and temperature effects on the mixed-mode delamination fracture of unidirectional graphite/epoxy. Delamination Debond Mater ASTM STP 876 (1985) 349-370
15. Forte M.S., Whitney M.J., and Schoeppner G.A. The influence of adhesive reinforcement on the mode I fracture toughness of a bonded joint. Compos Sci Technol 60 (2000) 2389-2405
16. Shetty S.P., and Spearing S.M. Fracture resistance of a fiber-reinforced film adhesive. Scripta Mater 37 6 (1997) 787-792
17. Norsok Standard M-501. Surface preparation and protective coating. Oslo: Norwegian Technology Standard Institution; 1999.
18. ISO 8501. Preparation of steel substrates before application of paints and related products. International Standard Organization; 2001.
19. ISO 8503. Preparation of steel substrates before application of paints and related products. International Standard Organization; 2003.
20. Whitney J.M., Browning C.E., and Hoogsteden W. A double cantilever beam test for characterizing mode I delamination of composite materials. J Reinf Plast Compos 1 (1982) 297
21. Davies P. Influence of ENF specimen geometry and friction on the mode II delamination resistance of carbon/PEEK. J Thermoplast Compos Mater 10 (1997) 353-361
22. Aksoy A., and Carlsson L.A. Crack tip yield zone estimates in mode II interlaminar fracture of interleaved composites. Eng Fract Mech 39 3 (1991) 525-534
23. Yang Q.D., Thouless M.D., and Ward S.M. Elastic-plastic mode II fracture of adhesive joints. Int J Solids Struct 38 (2001) 3251-3262
24. Abaqus, Inc. Abaqus analysis user manual, vol. IV, version 6.5. ABAQUS Inc. RI 02909-2499.
25. Ashby MF, Jones DRH. Engineering materials 1. Int Ser Mater Sci Technol; 1980 34.
26. Echtermeyer AT, Ronold KO, Breuil O, Palm S, Hayman B, Noury P, et al. Project offshore standard - Composite Components. DNV technical report 2002-0124 (2002) now published as offshore standard DNV-OS-C501. Composite components, Det Norske Veritas, Høvik, Norway; 2003.
27. Lubin G. Handbook of composites (1984), Van Nostrand Reinhold, New York p. 701
28. Hart-Smith LJ. Adhesive-bonded double-lap joints. NASA CR-112235, January; 1973.
29. Tsai S.W. Compositte design. Think composites. 4th ed (1988)
30. Echtermeyer A.T. Evaluation of the [±45°]s inplane shear test method for composites reinforced by multiaxial mabrics. Proceedings of the second European conference on composite testing and standardisation (1994)
31. Reeder J.R., and Crews Jr. J.H. Mixed-mode bending method for delamination testing. AIAA J 28 7 (1990) 1270-1276
32. Reeder JR, Crews Jr JH. Nonlinear analysis and redesign of the mixed-mode bending delamination test. NASA TM-102777; January 1991.