Performance characteristics of some "rough surfaces" with tube inserts for single-phase flow

Journal of Enhanced Heat Transfer

Volumn 13, Issue 2, 2006, Pages 117-137

  Zimparov, Ventsislav D ^a   Penchev, Plamen J ^a   Bergles, Arthur E ^b  

^a TECHNICAL UNIVERSITY OF GABROVO   (Bulgaria)

^b UNIVERSITY OF MARYLAND   (United States)

Author keywords

Cmpound heat transfer enhancement; Performance evaluation criteria; Rough tubes with tube inserts

Indexed keywords

COMPOUND HEAT TRANSFER ENHANCEMENT; PERFORMANCE EVALUATION CRITERIA; ROUGH TUBES WITH TUBE INSERTS;

HEAT EXCHANGERS; OPTIMAL CONTROL SYSTEMS; SURFACE PROPERTIES; THERMODYNAMIC PROPERTIES;

HEAT TRANSFER;

EID: 33749486178     PISSN: 10655131     EISSN: None     Source Type: Journal    
DOI: 10.1615/JEnhHeatTransf.v13.i2.30     Document Type: Conference Paper

References (21)

1. Bejan, A. (1982) Entropy Generation through Heat and Fluid Flow, John Wiley & Sons, New York.
2. Bejan, A. (1996) Entropy Generation Minimization, CRC Press, Boca Raton, FL.
3. Bergles, A. E. (2002) ExHFT for Fourth Generation Heat Transfer Technology, Exp. Thermal Fluid Sci., Vol. 26, Nos. 2-4, pp. 335-344.
4. Bergles, A. E., Lee, R. A., and Mikic, B. B. (1969) Heat Transfer in Rough Tubes with Tape-Generated Swirl Flow, J. Heat Transfer, Vol. 91, pp. 443-445.
5. Bergles, A. E., Blumenkrantz, A. R., and Taborek, J. (1974) Performance Evaluation Criteria for Enhanced Heat Transfer Surfaces, in Heat Transfer 1974, Proc. Fifth Int. Heat Transfer Conf., The Japan Society of Mechanical Engineers, Tokyo, Vol. II, pp. 234-238.
6. Bergles, A. E., Jensen, M. K., and Shome, B. (1995) Bibliography on Enhancement of Convective Heat and Mass Transfer, RPI Heat Transfer Laboratory Report HTL-23. Introduction in J. Enhanced Heat Transfer, Vol. 4, pp. 1-6.
7. Hasim, F., Yoshida M., and Miyashita H. (2003a) Compound Heat Transfer Enhancement by a Combination of Ribbed Tubes with Wire Coil Inserts, J. Chem. Eng. Japan, Vol. 36, No. 6, pp. 647-654.
8. Hasim, F., Yoshida M., and Miyashita H. (2003b) Compound Heat Transfer Enhancement by a Combination of Helically Ribbed Tubes with Twisted Tape Inserts, J. Chem. Eng. Japan, Vol. 36, No. 9, pp. 1116-1122.
9. Liao, Q. and Xin, M. D. (2000) Augmentation of Convective Heat Transfer Inside Tubes with Three-Dimensional Internal Extended Surface and Twisted Tape Inserts, Chem. Eng. J., Vol. 78, Nos. 2-3, pp. 95-105.
10. Manglik, R. M. and Bergles, A. E. (2004) Enhanced Heat Transfer in the New Millenium: A Review of the 2001 Literature, J. Enhanced Heat Transfer, Vol. 11, No. 2, pp. 87-118.
11. Marner, W. J., Bergles, A. E., and Chenoweth, J. M. (1983) On the Presentation of Performance Data for Enhanced Tubes Used in Shell-and-Tube Heat Exchangers, J. Heat Transfer, Vol. 105, pp. 358-365.
12. Shivkumar, C. and Raja Rao, M. (1988) Studies on Compound Augmentation of Laminar Flow Heat Transfer to Generalized Power Law Fluids in Spirally Corrugated Tubes by Means of Twisted Tape Inserts, Proc. 1988 Nat. Heat Transfer Conf., ASME-HTD-96, Vol. 1, ASME, New York, pp. 685-691.
13. Usui, N., Sano, Y., Iwashita, K., and Isozaki, A. (1986) Enhancement of Heat Transfer by a Combination of an Internally Grooved Rough Tube and a Twisted Tape, Int. Chem. Eng., Vol. 26, No. 1, pp. 97-104.
14. Van Rooyen, R. S. and Kroeger, D. G. (1978) Laminar Flow Heat Transfer in Internally Finned Tubes with Twisted-Tape Inserts, in Heat Transfer 1978, Hemisphere Publishing, Washington, DC, Vol. 2, pp. 577-581.
15. Webb, R. L. (1981) Performance Evaluation Criteria for Use of Enhanced Heat Exchanger Surfaces in Heat Exchanger Design", Int. J. Heat Mass Transfer, Vol. 24, pp. 715-726.
16. Zhang, Y. M., Han, J. C., and Lee, C. P. (1997) Heat Transfer and Friction Characteristics of Turbulent Flow in Circular Tubes with Twisted Tape Inserts and Axial Interrupted Ribs, J. Enhanced Heat Transfer, Vol. 4, pp. 297-308.
17. Zimparov, V. D. (2000) Extended Performance Evaluation Criteria for Enhanced Heat Transfer Surfaces: Heat Transfer through Ducts with Constant Wall Temperature, Int. J. Heat Mass Transfer, Vol. 43, No. 17, pp. 3137-3155.
18. Zimparov, V. D. (2001a) Enhancement of Heat Transfer by a Combination of Three-Start Spirally Corrugated Tubes with a Twisted Tape, Int. J. Heat Mass Transfer, Vol. 44, No. 3, pp. 551-574.
19. Zimparov, V. D. (2001b) Extended Performance Evaluation Criteria for Enhanced Heat Transfer Surfaces: Heat Transfer through Ducts with Constant Heat Flux, Int. J. Heat Mass Transfer, Vol. 44, No. 1, pp. 169-180.
20. Zimparov, V. D. (2002) Enhancement of Heat Transfer by a Combination of a Single-Start Spirally Corrugated Tubes with a Twisted Tape, Exp. Thermal Fluid Sci., Vol. 25, pp. 535-546.
21. Zimparov, V. D. and Penchev, P. J. (2004) Compound Heat Transfer Enhancement - Performance Characteristics of Some "Rough Surfaces" with Twisted Tape Inserts, in Proc. ASME-ZSIS, ITSS-II, Bled, Slovenia, June 13-16, 2004, pp. 975-982.