Dry wear properties of A356-SiC particle reinforced MMCs produced by two melting routes

Materials and Design

Volumn 27, Issue 10, 2006, Pages 872-881

  Yalcin, Y ^a   Akbulut, H ^b  

^a AFYON KOCATEPE UNIVERSITY   (Turkey)

^b SAKARYA UNIVERSITY   (Turkey)

Author keywords

Diluted composite; Microstructure; MMCs; Vortex method; Wear

Indexed keywords

CHARACTERIZATION; MELTING; MICROSTRUCTURE; SCANNING ELECTRON MICROSCOPY; SILICON CARBIDE; WEAR RESISTANCE;

DILUTED COMPOSITE; MELTING ROUTES; PARTICLE REINFORCED METAL MATRIX COMPOSITES; VORTEX METHOD; WEAR PROPERTIES;

METALLIC MATRIX COMPOSITES;

CHARACTERIZATION; MELTING; METALLIC MATRIX COMPOSITES; MICROSTRUCTURE; SCANNING ELECTRON MICROSCOPY; SILICON CARBIDE; WEAR RESISTANCE;

EID: 33746216719     PISSN: 02613069     EISSN: 18734197     Source Type: Journal    
DOI: 10.1016/j.matdes.2005.03.007     Document Type: Article

References (18)

1. Rodriguez J., Martin A., and Llorca J. Modeling the effect of temperature on the wear resistance of metals reinforced with ceramic particles. Acta Mater 48 (2000) 993-1003
2. Deuis R.L., Subramanian C., and Yellup J.M. Dry sliding wear of aluminum composites-a review. Compos Sci Technol 57 (1997) 415-425
3. Ravikiran A., and Surappa M.K. Effect of sliding speed on wear behavior of A 356 Al-30 wt% SiCp MMC. Wear 206 (1997) 33-38
4. Staffelini G., Pellizzari M., and Molinari A. Influence of load and temperature on the dry sliding behaviour of Al-based metal-matrix-composites against friction material. Wear 256 (2004) 754-763
5. Gul F., and Acilar M. Effect of the reinforcement volume fraction on the dry sliding wear behaviour of Al-10Si/SiCp composites produced by vacuum infiltration technique. Compos Sci Technol 64 (2004) 1959-1970
6. p/Al-Si metal matrix composites for automobile air-conditioner compressor pistons. J Mater Proc Technol 113 (2001) 202-208
7. Narciso J., Louis E., and Cordovilla C.G. Abrasive wear resistance of aluminum alloy/ceramic particulate composites. Wear 192 (1996) 170-177
8. Molina J.M., Saravanan R.A., Arpon R., Cordovilla C.G., Louis E., and Narciso J. Pressure infiltration of liquid aluminium into packed SiC particulate with a bimodal size distribution. Acta Mater 50 (2002) 247-257
9. Zhang J.S., Liu X.J., Cui H., Duan X.J., Sun Z.Q., and Chen G.L. Microstructure and properties of spray-deposited 2014 + 15 vol pct SiC particulate-reinforced metal matrix composite. Metall Trans A 28 (1997) 1261-1269
10. 3 short fiber reinforced Al-Si (LM 13) alloy metal matrix composites. Wear 215 (1998) 170-179
11. Bindumadhavan P.N., Chia T.K., Chandrasekaran M., Wah H.K., Lam L.N., and Prabhakar O. Effect of particle-porosity clusters on tribological behavior of cast aluminum alloy A356-SiCp metal matrix composites. Mater Sci Eng A 315 (2001) 217-226
12. 3-reinforced aluminium-based MMCs. Compos Sci Technol 61 (2001) 2381-2392
13. Shen Y.L., Williams J.J., Piotrowski G., Chawla N., and Guo Y.L. Correlation between tensile and indentation behavior of particle-reinforced metal matrix composites: an experimental and numerical study. Acta Mater 49 (2001) 3219-3229
14. Ravikiran A., and Surappa M.K. Effect of sliding speed on the wear behavior of A356 Al-30 wt SiCp MMC. Wear 206 (1997) 33-38
15. Roy M., Venkataraman B., Bhanuprasad V.V., Mahajan Y.R., and Sundararajan G. The effect of particulate reinforcement on the sliding wear behavior of aluminum matrix composites. Metall Trans A 25 (1992) 2833-2847
16. Rana F., and Stefanescu D.M. Friction properties of Al-1.5 pct Mg/SiC particulate metal matrix composites. Metall Trans A 20 (1989) 1564-1566
17. Saravanan R.A., Lee J.M., and Kang S.B. Dry sliding wear of A 356-15 pct SiCp composites under controlled atmospheric conditions. Metall Trans A 30 (1999) 2523-2538
18. Ravikiran A., and Surappa M.K. Oscillations in coefficient of friction during dry sliding of A356 Al-30% wt SiCp MMC against steel. Scripta Mater 36 (1997) 95-98