Structural design of high-strength austenitic stainless steel

Thin-Walled Structures

Volumn 44, Issue 5, 2006, Pages 517-528

  Gardner, L ^a   Talja, A ^b   Baddoo, N R ^c  

^a IMPERIAL COLLEGE LONDON   (United Kingdom)

^b VTT TECHNICAL RESEARCH CENTRE OF FINLAND   (Finland)

^c Steel Construction Institute   (United Kingdom)

Author keywords

Austenitic; Coldworked; Deformation capacity; Eurocode 3; High strength; Laboratory testing; Numerical modelling; Stainless steel; Structures

Indexed keywords

BUILDING CODES; CARBON STEEL; COMPOSITION; STEEL STRUCTURES; STRENGTH OF MATERIALS; STRUCTURAL DESIGN;

AUSTENITIC; COLDWORKED; DEFORMATION CAPACITY; EUROCODE 3; HIGH STRENGTH; LABORATORY TESTING; NUMERICAL MODELLING;

STAINLESS STEEL;

EID: 33746034152     PISSN: 02638231     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.tws.2006.04.014     Document Type: Article

References (17)

1. Gardner L. The use of stainless steel in structures. Prog Struct Eng Mater 7 2 (2005) 45-55
2. prEN 1993-1-4. Eurocode 3: design of steel structures-part 1.4: general rules-supplementary rules for stainless steel, CEN, 2005.
3. EN 10088-2. Stainless steels-part 2: technical delivery conditions for sheet/plate and strip for general purposes. CEN, 2005.
4. Young B., and Lui W- M. Behavior of cold-formed high strength stainless steel sections. J Struct Eng, ASCE 131 11 (2005) 1738-1745
5. Ellobody E., and Young B. Structural performance of cold-formed high strength stainless steel columns. J Constr Steel Res 61 12 (2005) 1631-1649
6. Talja, A. WP2: structural hollow sections and WP3: cold-formed profiles and sheeting-test results of RHS, tophat and sheeting profiles. ECSC project: structural design of cold-worked austenitic stainless steel. Contract no. 7210 PR318. VTT Building Technology, Finland, 2003.
7. Gardner, L. WP2: structural hollow sections-numerical modelling of high strength stainless steel hollow sections and development of design guidance. ECSC project: Structural design of cold-worked austenitic stainless steel. Contract no. 7210 PR318, Department of Civil and Environmental Engineering, Imperial College, London, 2003.
8. ABAQUS. ABAQUS/ standard user's manual vols. I-III and ABAQUS post manual. Version 6.3. Pawtucket USA.Hibbitt, Karlsson & Sorensen, Inc.;2003.
9. Real, E. Aportaciones al estudio del comportamiento a flexion de estructuras de acero inoxiddable. Tesis Doctoral. Departamento de Ingeniería de la Construcción, Universitat Politècnica de Catalunya. UPC-ETSECCP. Barcelona, Mayo, 2001 [In Spanish].
10. Gardner L., and Nethercot D.A. Numerical modelling of stainless steel structural components-a consistent approach. J Struct Eng, ASCE 130 10 (2004) 1586-1601
11. Mirambell E., and Real E. On the calculation of deflections in structural stainless steel beams: an experimental and numerical investigation. J Constr Steel Res 54 1 (2000) 109-133
12. Gardner, L. A new approach to stainless steel structural design. PhD. thesis, Structures Section, Department of Civil and Environmental Engineering, Imperial College London.
13. Rasmussen K.J.R. Full range stress-strain curves for stainless steel alloys. J Constr Steel Res 59 1 (2003) 47-61
14. Gardner L., and Nethercot D.A. Stainless steel structural design: a new approach. Struct Eng 82 21 (2004) 21-28
15. Gardner L., and Ashraf M. Structural design for non-linear metallic materials. Eng Struct 28 6 (2006) 926-934
16. prEN 1993-1-3. (2005). Eurocode 3: design of steel structures-part 1.3: General rules-supplementary rules for cold formed thin gauge members and sheeting. CEN, 2005.
17. Talja A, and Salmi P. (1995). Design of stainless steel RHS beams, columns and beam-columns. Research Note 1619, VTT Building Technology, Finland.