Generalized stress intensity factors due to steady and transient thermal loads with applications to welded joints

Fatigue and Fracture of Engineering Materials and Structures

Volumn 29, Issue 6, 2006, Pages 440-453

  Ferro, P ^a   Berto, F ^a   Lazzarin, P ^a  

^a UNIVERSITY OF PADOVA   (Italy)

Author keywords

Asymptotic stress distribution; Elasticity; Notch stress intensity factor; Plasticity; Thermal load; V notch

Indexed keywords

ALUMINUM; COMPUTER SIMULATION; ELASTICITY; FINITE ELEMENT METHOD; HEAT TRANSFER; ORDINARY DIFFERENTIAL EQUATIONS; PLASTICITY; RESIDUAL STRESSES; STRAIN; STRESS CONCENTRATION; STRESS INTENSITY FACTORS; THERMAL LOAD;

ALUMINUM BUTT-WELDED JOINT; ASYMPTOTIC STRESS DISTRIBUTION; NOTCH STRESS INTENSITY FACTOR; SHARP V-NOTCH TIPS;

WELDS;

EID: 33745805857     PISSN: 8756758X     EISSN: 14602695     Source Type: Journal    
DOI: 10.1111/j.1460-2695.2006.01015.x     Document Type: Article

References (33)

1. Williams, M. L. (1952) Stress singularities resulting from various boundary conditions in angular corners of plates in extension. J. Appl. Mech. 19, 526-528.
2. Hutchinson, J. W. (1968) Singular behaviour at the end of a tensile crack in a hardening material. J. Mech. Phys. Solids 16, 13-31.
3. Rice, J. R. and Rosengren, G. F. (1968) Plane strain deformation near a crack tip in a power-law hardening material. J. Mech. Phys. Solids 16, 1-12.
4. Ponte Castañeda, P. (1985) Asymptotic fields in steady crack growth with linear strain-hardening. J. Mech. Phys. Solids 35, 227-268.
5. Xia, L. and Wang, T. (1993) Singular behavior near the tip of a sharp V-notch in a power-hardening material. Int. J. Fracture 59, 83-93.
6. Yuan, H. and Lin, G. (1994) Analysis of elastoplastic sharp notches. Int. J. Fracture 67, 187-216.
7. Lazzarin, P., Zambardi, R. and Livieri, P. (2001) Plastic notch stress intensity factors for large V-shaped notches under mixed load conditions. Int. J. Fracture 107, 361-377.
8. Radaj, D. (1990) Design and analysis of fatigue resistant welded structures. Abington Publishing, Cambridge.
9. Radaj, D. (1996) Review of fatigue strength assessment of non welded and welded structures based on local parameters. Int. J. Fatigue 18, 153-170.
10. Boukharouba, T., Tamine, T. and Nui, L. et al. (1995) The use of notch stress intensity factor as a fatigue crack initiation parameter. Eng. Fract. Mech. 52, 503-512.
11. Verreman, Y. and Nie, B. (1996) Early development of fatigue cracking at manual fillet welds. Fatigue Fract. Engng, Mater. Struct. 19, 669-681.
12. Lazzarin, P. and Tovo, R. (1998) A notch intensity approach to the stress analysis of welds. Fatigue Fract. Engng. Mater. Struct. 21, 1089-1104.
13. Atzori, B., Lazzarin, P. and Tovo, R. (1999) From the local stress approach to fracture mechanics: A comprehensive evaluation of the fatigue strength of welded joints. Fatigue Fract. Engng. Mater. Struct. 22, 369-381.
14. Lazzarin, P. and Livieri, P. (2001) Notch Stress Intensity Factors and fatigue strength of aluminium and steel welded joints. Int. J. Fatigue 23, 225-232.
15. Atzori, B. and Meneghetti, G. (2001) Fatigue strength of fillet welded structural steels: Finite elements, strain gauges and reality. Int. J. Fatigue 23, 713-721.
16. Beghini, M., Bertini, L. and Vitale, E. (1994) Fatigue residual stress fields. Experimental results and modelling. Fatigue Fract. Engng. Mater. Struct. 17, 1433-1444.
17. Mochizuki, M., Hattori, T. and Navakano, K. (2000) Residual stress reduction and fatigue strength improvement by controlling welding pass sequences. J. Eng. Mat. Tech. 122, 108-112.
18. Stern, M. (1979) The numerical study calculation of thermally induced stress intensity factors. J. Elasticity 9, 91-95.
19. Babuşka, I. and Miller, A. (1984) The post-processing approach in the finite element method -Part 2: The calculation of stress intensity factors. Int. J. Numer. Methods Eng. 20, 1111-1129.
20. Szabó, B. A. and Yosibash, Z. (1996) Numerical analysis of singularities in two-dimensions. Part 2: Computation of the generalized flux/stress intensity factors. Int. J. Numer. Methods Eng. 39, 409-434.
21. Yosibash, Z. (1997) On solutions of two-dimensional linear elastostatic and heat-transfer problems in the vicinity of singular points. Int. J. Solids Struct. 34, 243-274.
22. Yosibash, Z. (1998) Thermal generalized stress intensity factors in 2D domains. Comput. Methods Appl. Mech. Engng. 157, 365-385.
23. Gross, R. and Mendelson, A. (1972) Plane elastostatic analysis of V-notched plates. Int. J. Fract. Mech. 8, 267-276.
24. Cañas, J., Picòn, R. and París, F. et al. (1996) A simplified numerical analysis of residual stresses in aluminium welded plates. Comput. Struct. 58, 59-69.
25. Zhu, X. K. and Chao, Y. J. (2002) Effects of temperature-dependent material properties on welding simulation. Comput. Struct. 80, 967-976.
26. Ferro, P., Zambon, A. and Bonollo, F. (2005) Investigation of electron-beam welding in wrought Inconel 706-experimental and numerical analysis. Mater. Sci. Eng. A 392, 94-105.
27. Mok, D. H. B. and Pick, R. J. (1991) Finite element study of residual stresses in a plate T-joint fatigue specimen. Int. J. Fatigue 13, 281-291.
28. Sarkani, S., Tritchkov, V. and Michaelov, G. (2000) An efficient approach for computing residual stresses in welded joints. Finite Elements Anal. Design 35, 247-268.
29. Teng, T. L., Fung, C. P. and Chang, P. H. et al. (2001) Analysis of residual stresses and distortions in T-joint fillet welds. Int. J. Pressure Vessels Piping 78, 523-538.
30. Goldak, J., Chakravarti, A. and Birbby, M. (1984) A new finite element model for welding heat sources. Metallur. Trans. B 15b, 299-305.
31. Bertini, L., Fontanari, V. and Straffellini, G. (1998) Influence of post weld treatments on fatigue behaviour of Al-alloy welded joints. Int. J. Fatigue 20, 749-755.
32. Ferro, P., Bonollo, F. and Tiziani, A. et al. (2004) A review of welding process numerical simulation: Methods and experimental validations. Proceedings 2nd International Conference & Exhibition on New Developments in Metallurgical Process Technology, Riva del Garda, Italy, 19-21 September 2004. Organized by AIM.
33. Ferro, P., Porzner, H. and Tiziani, A. et al. (2006) The influence of phase transformations on residual stresses induced by the welding process - 3D and 2D numerical models'. Model. Simul. Mater. Sci. Engng 14, 117-136.