Enhanced impingement heat transfer: The influence of impingement X/D for interrupted rib obstacles (rectangular pin fins)

Journal of Turbomachinery

Volumn 128, Issue 2, 2006, Pages 321-331

  Andrews, G E ^a   Abdul Hussain, R A A ^a   Mkpadi, M C ^a  

^a UNIVERSITY OF LEEDS   (United Kingdom)

Author keywords

[No Author keywords available]

Indexed keywords

COMBUSTORS; COOLING; DETERIORATION; FINS (HEAT EXCHANGE); PRESSURE; THERMAL EFFECTS;

COMBUSTOR WALL COOLING; COOLING PRESSURE; CROSS FLOW; ENHANCED IMPINGEMENT HEAT TRANSFER; FLOW RATE; PRESSURE LOSS; RIB OBSTACLES;

HEAT TRANSFER;

COMBUSTORS; COOLING; DETERIORATION; FINS (HEAT EXCHANGE); HEAT TRANSFER; PRESSURE; THERMAL EFFECTS;

EID: 33745289116     PISSN: 0889504X     EISSN: None     Source Type: Journal    
DOI: 10.1115/1.1860574     Document Type: Article

References (28)

1. x Radial Swirler Gas Turbine Combustor," ASME Paper No. 2001-GT-0071.
2. Son, C. Gillespie, D., Ireland, P., and Dailey G. M., 2001, "Heat Transfer Characteristics of an Impingement Plate Used in a Turbine Vane Cooling System," ASME Paper No. 2001-GT-154.
3. Haiping, C., Dalin, Z., and Taiping H., 1997, "Impingement Heat Transfer From Rib Roughened Surface Within Arrays of Circular Jets: The Effect of the Relative Position of the Jet Hole to the Rib," ASME Paper No. 97-GT-331.
4. Haiping, C., Jingyu, Z., and Taipping, H., 1998, "Experimental Investigation on Impingement Heat Transfer From Rib Roughened Surface Within Arrays of Circular Jets: Effect of Geometric Parameters," ASME Paper No. 98-GT-208.
5. Hoecker, R., Johnson, B. V., Hausladen, J., Rothbrust, M., and Weigand, B., 1999, "Impingement Cooling Experiments With Flat and Pin Plate Target Surfaces," ASME Paper No. 99-GT-252.
6. Annerfeldt, M. O., Persson, J. L., and Torisson, T., 2001, "Experimental Investigation of Impingement Cooling With Turbulators or Surface Enlarging Elements," ASME Paper No. 2001-GT-149.
7. Chance, J. T., 1974, "Experimental Investigations of Air Impingement Heat Transfer Under an Array of Thermal Jets," Tappi J. 57, pp. 108-112.
8. Kercher, D. M., and Tabakoff, W., 1970, "Heat Transfer by a Square Array of Round Air Jets Impinging Perpendicular to a Flat Surface," ASME J. Eng. Power, 92, pp. 73-82.
9. Florschuetz, L. W., Truman, C. R., and Metzger, D. E., 1981, "Streamwise Flow and Heat Transfer Distribution for Jet Array Impingement With Initial Crossflow," ASME J. Heat Transfer 103, pp. 337-342.
10. Abdul Hussain, R. A. A., and Andrews, G. E., 1990, "Full Coverage Impingement Heat Transfer at High Temperatures," ASME Paper No. 90-GT-285.
11. Trabold, T. A., and Obot, N. T., 1987, "Impingement Heat Transfer Within Arrays of Circular Jets, Part II: Effects of Crossflow in the Presence of Roughness Elements," ASME Paper No. 87-GT-200.
12. Abdul Hussain, R. A. A., and Andrews, G. E., 1991, "Enhanced Full Coverage Impingement Heat Transfer With Obstacles in the Gap," ASME Paper No. 91-GT-346.
13. Andrews, G. E., and Hussain, C. I., 1986, "Full Coverage Impingement Heat Transfer: The Influence of Channel Height," Proc. of 8th Int. Heat Transfer Conference, Hemisphere, Washington, DC, pp. 1205-1211.
14. Andrews, G. E., and Hussain, C. I., 1987, "Full Coverage Impingement Heat Transfer: The Influence of Crossflow," AIAA Paper 87-2010.
15. Al Dabagh, A. M., Andrews, G. E., Abdul Husain, R. A. A., Husain, C. I., Nazari, A., and Wu, J., 1989, Impingement/Effusion Cooling: The Influence of the Number of Impingement Holes and Pressure Loss on the Heat Transfer coefficient, ASME Paper No. 89-GT-188.
16. Son, C. M., Gillespie, D. R. H., Ireland, P. T., and Dailey, G. M., 2000, "Heat Transfer and Flow Characteristics of an Engine Representative Impingement Cooling System," ASME Paper No. 2000-GT-219.
17. Shizuya, M., and Kawaike, K., 1987, "Experimental Investigation of Blade Internal Cooling Methods Using Ribs and Fins," Tokyo International Gas Turbine Congress, Paper 87-Tokyo-IGTC-65, Vol. III, pp. 159-166.
18. Chang, H. et al., 1997.
19. Chang, H., Jingyu, Z., and Taiping, H., 1998, "Experimental Investigation on Impingement Heat Transfer From Rib Roughened Surface Within Arrays of Circular Jet: Effect of Geometric Parameters," ASME Paper No. 98-GT-208.
20. Andrews, G. E., Abdul Hussain, R. A. A., and Mkpadi, M. C., 2003, "Enhanced Impingement Heat Transfer: Comparison of Co-flow and Cross-flow With Rib Turbulators," Proc. of Int. Gas Turbine Congress 2003 Tokyo, IGTC2003Tokyo TS-075.
21. Andrews, G. E., Asere, A. A., Hussain, C. I., and Mkpadi, M. C., 1985, "Full Coverage Impingement Heat Transfer: The Variation in Pitch to Diameter Ratio at Constant Gap," Heat Transfer and Cooling in Gas Turbines, AGARD CP 390 Paper No. 26, pp. 26-1-26-13.
22. Andrews, G. E., and Mkpadi, M. C., 1983, "Full Coverage Discrete Hole Wall Cooling: Discharge Coefficients," ASME Paper No. 83-GT-79.
23. Andrews, G. E., and Hussain, C. I., 1984, "Full Coverage Impingement Heat Transfer: The Influence of Impingement Jet Size," Proc. of 1st UK National Heat Transfer Conference, IChemE Symp. Ser. No. 86, pp. 1115-1124.
24. Tabakoff, W., and McFarlane, E. R., 1975, "Gas Turbine Blade Heat Transfer With Rough Surfaces," ASME Paper No. 75-WA/HT-107.
25. Han, J. C., 1984, "Heat Transfer and Friction in Channels With Two Opposite Rib-Roughened Walls," ASME J. Heat Transfer 106, pp. 774-781.
26. Son, C. M., Gillespie, D. R. H., Ireland, P. T., and Dailey, G. M., 2000, "Heat Transfer Enhancement Strategy for an Impingement Cooling System," Proc. of 8th Int. Symp. Tranport Phenomena and Dynamics of Rotating Machinery.
27. Bailey, J. C., and Bunker, R. S., 2002, "Local Heat Transfer and Flow Distributions for Impinging Jet Arrays of Dense and Sparse Extent," ASME Paper No. GT-2002-30473.
28. Andrews, G. E., Al Dabagh, A. M., Asere, A. A. A., Bazdidi-Tehrani, F., Mkpadi, M. C., and Nazari, A., 1992, "Impingement/Effusion Cooling," Heat Transfer and Cooling in Gas Turbines, Antalya, Turkey, AGARD CP 527, pp. 30-1-30-10.