Three-dimensional finite element method for the filling simulation of injection molding

Engineering with Computers

Volumn 21, Issue 4, 2006, Pages 289-295

  Tie, Geng ^a,b   Dequn, Li ^a   Huamin, Zhou ^a  

^a HUAZHONG UNIVERSITY OF SCIENCE AND TECHNOLOGY   (China)

^b HENAN UNIVERSITY OF TECHNOLOGY   (China)

Author keywords

3D; Equal order interpolation; Injection molding; Simulation

Indexed keywords

APPROXIMATION THEORY; CALCULATIONS; FINITE ELEMENT METHOD; INJECTION MOLDING; PRESSURE MEASUREMENT; TEMPERATURE MEASUREMENT; THREE DIMENSIONAL; VELOCITY MEASUREMENT;

HALE-SHAW APPROXIMATION; THREE-DIMENSIONAL SIMULATION MODEL;

COMPUTER SIMULATION;

EID: 33745077352     PISSN: 01770667     EISSN: 14355663     Source Type: Journal    
DOI: 10.1007/s00366-006-0018-x     Document Type: Article

References (14)

1. Gotoh Terumasa, Iizuka, Miyamoto Masayuki et al (1986) Simulation of polymeric flows in the cavity filling process of injection molding. Sharp Tech J 34:63-70
2. H Schlichting 1968 Boundary-layer theory McGraw-Hill New York
3. Chen BS, Liu WH (1989) Numerical simulation and experimental investigation of injection mold filling with melt solidification. Polym Eng Sci 29:1039-1050 10.1002/pen.760291510
4. Dequn L (2002) New progress of flow simulation for plastic injection molding. China Int Forum Die Mould Technol 5:47-48
5. Huamin Z, Dequn L (2002) Computer filling simulations of injection molding based on 3D surface model. Polym Plast Tech Eng 41:91-1021 10.1081/PPT-120002062
6. Hiebert CA, Shen SF (1980) A finite-element/finite-difference simulation of injection molding filling process. J Non-Newtonian Fluid Mesh 7:1-32 10.1016/0377-0257(80)85012-9
7. Inoue Y, Higashi T, Matsuoka T (1996) Numerical simulation of 3-dimensional flow in injection molding. ANTEC Proc 1:744-748
8. Pichelin E, Coupez T (1998) Finite element solution of the 3D filling problem for viscous incompressible fluid. Comput Methods Appl Mech Eng 163:359--371 10.1016/S0045-7825(98)00024-3
9. Hwang CJ, Kwon TH (2002) A full 3D finite element analysis of the powder injection molding filling process including slip phenomena. Polym Eng Sci 42:33-50 10.1002/pen.10926
10. Prakash C, Patankar SV (1985) A control volume-based finite-element method for solving the Navier-Stokes equations using equal-order velocity-pressure interpolation. Numer Heat Transfer 8:259-280 1985NumHT...8..259P
11. Prakash C (1986) An improved control volume finite-element method for heat and mass transfer, and for fluid flow using equal-order velocity-pressure interpolation. Numer Heat Transfer 9:253-276
12. Rice JG, Schnipe RJ (1986) An equal-order velocity-pressure formulation that does not exhibit spurious pressure modes. Comput Methods Appl Mech Eng 58:135-149 10.1016/0045-7825(86)90093-9
13. CA Hieber 1987 Injection and compression molding fundamentals Marcel Dekker New York
14. Tadmor Z, Broyer E, Gutfinger C (1974). Flow analysis method for solving flow problems in polymer processing. Polym Eng Sci 14:660-665 10.1002/ pen.760140913