Characteristics of powder lubricated finite-width journal bearings: A hydrodynamic analysis

Journal of Tribology

Volumn 128, Issue 2, 2006, Pages 351-357

  Tsai, Hung Jung ^a   Jeng, Yeau Ren ^b  

^a WUFENG INSTITUTE OF TECHNOLOGY   (Taiwan)

^b NATIONAL CHUNG CHENG UNIVERSITY   (Taiwan)

Author keywords

Eccentricity ratio; Flow rate; Grain flow; Grain grain collision elasticity; Granular flow; Hydrodynamic lubrication; Journal bearings

Indexed keywords

ELASTICITY; FRICTION; HYDRODYNAMICS; LUBRICATION; PARTICLE SIZE ANALYSIS; POWDERS;

ECCENTRICITY RATIO; FLOW RATE; GRAIN FLOW; GRAIN-GRAIN COLLISION ELASTICITY; GRANULAR FLOW; HYDRODYNAMIC LUBRICATION;

JOURNAL BEARINGS;

ELASTICITY; FRICTION; HYDRODYNAMICS; JOURNAL BEARINGS; LUBRICATION; PARTICLE SIZE ANALYSIS; POWDERS;

EID: 33646433012     PISSN: 07424787     EISSN: None     Source Type: Journal    
DOI: 10.1115/1.2162558     Document Type: Article

References (19)

1. Jeng, Y. R., and Tsai, H. J., 2002, "Grain-Flow Lubrication of Finite-Width Slider Bearings With Rough Surfaces," Tribol. Lett., 13(4), pp. 219-232.
2. McKeague, K. T., and Khonsari, M. M., 1996, "An Analysis of Powder Lubricated Slider Bearings," ASME J. Tribol., 118, pp. 206-214.
3. Batra, A., and Dareing, D. W., 1995, "Hydrodynamic Behavior of Graphite Powder Slurries in Journal Bearings," Tribol. Trans., 38, pp. 161-167.
4. Pappur, M., and Khonsari, M. M., 2003, "Flow Characterization and Performance of a Powder Lubricated Slider Bearing," ASME J. Tribol., 125, pp. 135-144.
5. Jeng, Y. R., and Tsai, H. J., 2002, "Tribological Analysis on Powder Slurry in Chemical Mechanical Polishing," J. Phys. D, 35, pp. 1585-1591.
6. Jeng, Y. R., and Tsai, H. J., 2003, "Improved Model of Wafer/Pad Powder Slurry for Chemical Mechanical Polishing," J. Electrochem. Soc., 150(6), pp. G348-G354.
7. Heshmat, H., 1992, "The Quasi-Hydrodynamic Mechanism of Powder Lubrication: Part 2. Lubricant Film Pressure Profile," Lubr. Eng., 48, pp. 373-383.
8. Kaur, R. G., and Heshmat, H., 2002, "100 mm Diameter Self-Contained Solid/Powder Lubricated Auxiliary Bearing Operated at 30,000 rpm," Lubr. Eng., 48, pp. 13-20.
9. 2 Powder: Experimental Study of Thermal Phenomena," ASME J. Tribol., 117, pp. 506-512.
10. 2 Powder: Experimental Study," ASME J. Tribol., 118, pp. 484-491.
11. Yu, C. M., Craig, K., and Tichy, J., 1994, "Granular Collision Lubrication," J. Rheol., 38(4), pp. 921-936.
12. Iordanoff, I., Berthier, Y., Descartes, S., and Heshmat, H., 2002, "A Review of Recent Approaches for Modeling Solid Third Bodies," ASME J. Tribol., 124, pp. 725-735.
13. Haff, P. K., 1983, "Grain Flow as a Fluid-Mechanical Phenomenon," J. Fluid Mech., 134, pp. 401-430.
14. Elrod, H. G., 1988, "Granular Flow as a Tribological Mechanism-A First Look," Interface Dynamics, Leeds-Lyon Conference, pp. 75-88.
15. Dai, F., Khonsari, M. M., and Lu, Y. Z., 1994, "On the Lubrication Mechanism of Grain Flows," Tribol. Trans., 37, pp. 516-524.
16. Lun, C. K. K., Savage, S. B., Jeffery, D. J., and Chepurniy, N., 1984, "Kinetic Theories for Granular Flows: Inelastic Particles in Couette Flow and Slightly Inelastic Particles in a General Flow Field," J. Fluid Mech., 140, pp. 223-256.
17. Zhou, L., and Khonsari, M. M., 2000, "Flow Characteristics of a Powder Lubricant Sheared Between Parallel Plates," ASME J. Tribol., 122, pp. 147-155.
18. Patankar, S. V., 1994, Numerical Heat Transfer and Fluid Flow, McGraw-Hill, New York.
19. Tsai, H. J., and Jeng, Y. R., 2002, "An Average Lubrication Equation for Thin Film Grain Flow With Surface Roughness Effects," ASME J. Tribol., 124, pp. 736-742.