Modeling of film cooling - Part I: Experimental study of flow structure

Journal of Turbomachinery

Volumn 128, Issue 1, 2006, Pages 141-149

  Bernsdorf, Stefan ^a   Rose, Martin G ^a   Abhari, Reza S ^a  

^a ETH ZURICH   (Switzerland)

Author keywords

Blowing ratio; Density ratio; Film cooling; Flow structure; PIV

Indexed keywords

CALIBRATION; COMPUTATIONAL FLUID DYNAMICS; COMPUTER SIMULATION; COOLANTS; HEATING; TURBOMACHINE BLADES; VELOCITY MEASUREMENT;

BLOWING RATIO; CYLINDRICAL HOLE GEOMETRIES; DIMENSIONAL VELOCITIES; FILM COOLING MODEL; PARTICLE IMAGE VELOCIMETRY;

COOLING;

CALIBRATION; COMPUTATIONAL FLUID DYNAMICS; COMPUTER SIMULATION; COOLANTS; COOLING; HEATING; TURBOMACHINE BLADES; VELOCITY MEASUREMENT;

EID: 33645794586     PISSN: 0889504X     EISSN: None     Source Type: Journal    
DOI: 10.1115/1.2098768     Document Type: Article

References (28)

1. Burdet, A., and Abhari, R. S., The Modelling of Film Cooling - Part II: Model for Use in 3D CFD, ASME Paper No. GT2005-68780.
2. Abhari, R. S., 1996, "Impact of Rotor-Stator Interaction on Turbine Blade Film Cooling," J. Turbomach., 118, pp. 123-133.
3. Abhari, R. S., and Epstein, A. H., 1994, "An experimental Study of Film Cooling in a Rotating Transonic Turbine," J. Turbomach., 116, pp. 63-70.
4. Abhari, R. S., Guenette, G. R., Epstein, A. H., and Giles, M. B., 1992, "Comparison of Time-Resolved Turbine Rotor Blade Heat Transfer Measurements and Numerical Calculations," J. Turbomach., 114, pp. 818-827.
5. Dunn, M. G., 1990, "Phase and Time Resolved Measurements of Unsteady Heat Transfer and Pressure in a Full-Stage Rotating Turbine, "J. Turbomach., 112, pp. 531-538.
6. Eads, T. A., 1992, "Shock Tube Study of the Effects of Large Density Differences and Blowing Ratio on Heat Transfer to a Film-Cooled Flat Plate," MSc, Wright-Patterson AFB, Ohio School of Engineering.
7. Giang, T. T. L., 1999, "Effects of Unsteady Cooling Flow on Heat Transfer to a Film-Cooled Flat Plate," MSc, The Ohio State University, Columbus.
8. Guenette, G. R., Epstein, A. H., Giles, M. B., and Haimes, R., 1989, "Fully scale Transonic Turbine Rotor Heat Transfer Measurements," J. Turbomach., 111, pp. 1-7.
9. Teekaram, A. J. H., Forth, C. J. P., and Jones, T. V., 1989, "The Use of Foreign Gas to Simulate the Effects of Density Ratios in Film Cooling," ASME J. Turbomach., 111(1), pp. 57-62.
10. Goldstein, R. J., and Jin, P., "Film Cooling Downstream of a Row of Discrete Holes with Compound Angle," Proceedings of the ASME Turbo Expo 2000.
11. Ligrani, P. M., and Bell, C. M., 2001, "Film Cooling Subject to Bulk Flow Pulsations: Effects of Density Ratio, Hole Length-to-Diameter Ratio, and Pulsation Frequency," Int. J. Heat Mass Transfer, 44(10), pp. 2005-2009.
12. Ligrani, P. M., Saumweber, C., Schulz, S., and Wittig, S., 2001, "Shock Wave - Film Cooling Interactions in Transonic Flows," ASME J. Turbomach., 123(4), pp. 788-797.
13. Pietrzyk, J. R., Bogard, B. G., and Crawford, M. E., 1989, "Experimental Study of the Interaction of Dense Jets With a Crossflow for Gas Turbine Applications," 89-1, Turbulence and Turbine Cooling Research Laboratory, Mechanical Engineering Department, The University of Texas at Austin, Austin, TX.
14. Cho, H. H., and Goldstein, R. J., 1995, "Heat (Mass) Transfer and Film-Cooling Effectiveness With Injection through Discrete Holes on the Exposed Surface," ASME J. Turbomach., 117(3), pp. 451-460.
15. Forth, C. J. P., Loftus, P. J., and Jones, T. V., 1985, "Effect of Density Ratio on the Film-Cooling of a Flat Plate," AGARD Conf. Proc., CP 390, pp. 113-143.
16. Popp, O., Smith, D. E., Bubb, J. V., Grabowski, H. C., Diller, T. E., Schetz, J. A., and Ng, W. F., "An Investigation of Heat Transfer in a Film Cooled Transonic Turbine Cascade, Part I: Steady Heat Transfer," Proceedings of the ASME Turbo Expo 2000.
17. Smith, D. E., Bubb, J. V., Popp, O., Grabowski, H. C., Diller, T. E., Schetz, J. A., and Ng, W. F., "An Investigation of Heat Transfer in a Film Cooled Transonic Turbine Cascade, Part II: Unsteady Heat Transfer," Proceedings of the ASME Turbo Expo 2000.
18. Dunn, M. G., and Hause, A., 1982, "Measurement of Heat Flux and Pressure in a Turbine Stage," J. Eng. Power, 104, pp. 215-223.
19. Goldstein, R. J., Eckert, E. R. G., and Burggraf, F., 1974, "Effects of Hole Geometry and Density on 3-Dimensional Film Cooling," Int. J. Heat Mass Transfer, 17(5), pp. 595-607.
20. Bons, J. P., MacArthur, C. D., and Rivir, R. B., 1996, "The Effect of High Freestream Turbulence on Film Cooling Effectiveness," ASME J. Turbomach., 118(4), pp. 814-825.
21. Gogineni, S., Goss, L., Pestian, D., and Rivir, R., 1998, "Two-Colour Digital PIV Employing a Single CCD Camera," Exp. Fluids, 25(4), pp. 320-328.
22. Rockwell, R. K., 1989, "Transient Heat Transfer Measurements on a Flat Plate in Turbulent Flow Using an Electrical Analog," MSc, Air Force Institute of Technology, Wright-Patterson Air Force Base, OH.
23. Ekkad, S. V., Zapata, D., and Han, J. C., 1997, "Heat Transfer Coefficients Over a Flat Surface With Air and CO2 Injection Through Compound Angle Holes Using a Transient Liquid Crystal Image Method," ASME J. Turbomach., 119(3), pp. 580-586.
24. Honami, S., Shizawa, T., and Uchiyama, A., 1994, "Behaviour of the Laterally Injected Jet in Film-Cooling - Measurements of Surface-Temperature and Velocity/Temperature Field Within the Jet," ASME J. Turbomach., 116(1), pp.106-112.
25. Epstein, A. H., Guenette, G. R., Norton, R. J. G., and Yuzhang, C., 1986, "High Frequency Response Heat Flux Gauge for Metal Blading," Rev. Sci. Instrum., 57(4), pp. 639-649.
26. Goldstein, R. J., and Cho, H. H., 1995, "A Review of Mass-Transfer Measurements Using Naphthalene Sublimation," Exp. Therm. Fluid Sci., 10(4), pp. 416-434.
27. Le Grivèe, E., 1978, "Mixing Process Induced by the Vorticity Associated With the Penetration of a Jet Into a Cross Flow," J. Eng. Power, 100.
28. 2002, "Flow Manager Software and Introduction to PIV Instrumentation," Dantec Dynamics A/S.