Measured film cooling effectiveness of three multihole patterns

Journal of Heat Transfer

Volumn 128, Issue 2, 2006, Pages 192-197

  Lin, Yuzhen ^a   Song, Bo ^a,b   Li, Bin ^a,c   Liu, Gaoen ^a  

^a BEIHANG UNIVERSITY   (China)

^b Gardner Denver Inc   (United States)

^c China Gas Turbine Institute   (China)

Author keywords

Adiabatic film cooling effectiveness; Blowing ratio; Heat mass transfer analogy; Multihole pattern

Indexed keywords

BLOWING RATIO; FILM COOLING; HEAT-MASS TRANSFER ANALOGY; MULTIHOLE PATTERN;

COOLING; FILMS; MASS TRANSFER; THERMAL VARIABLES MEASUREMENT;

HEAT TRANSFER;

COOLING; FILMS; HEAT TRANSFER; MASS TRANSFER; THERMAL VARIABLES MEASUREMENT;

EID: 33645791480     PISSN: 00221481     EISSN: None     Source Type: Journal    
DOI: 10.1115/1.2137762     Document Type: Article

References (19)

1. Mellor, A. M., 1991, Design of Modern Turbine Combustor, Academic, New York.
2. Mayle, R. E., and Camarata, F. J., 1975, "Mutihole Cooling Film Effectiveness and Heat Transfer," ASME J. Heat Transfer, 97(2), pp. 534-538.
3. Sasaki, M., Takahara, K., Kumagai, T., and Hanano, M., 1979, "Film Cooling Effectiveness for Injection From Multirow Holes," ASME J. Eng. Power, 101(1), pp. 101-108.
4. Martiny, M., Schulz, A., and Wittig, S., 1995, "Full-Coverage Film Cooling Investigations: Adiabatic Wall Temperatures and Flow Visualization," ASME Paper No. 95-WA/HT-4.
5. Andrews, G. E., Khalifa, I. M., Asere, A. A., and Bazdidi-Tehrani, F., 1995, "Full Coverage Effusion Film Cooling with Inclined Holes," ASME Paper No. 95-GT-274.
6. Metzger, D. E., Takeuchi, D. I., and Kuenstler, P. A., 1973, "Effectiveness and Heat Transfer with Full Coverage Film Cooling," ASME Paper No. 73-GT-18.
7. Andrews, G. E., Gupta, M. L., and Mkpadi, M. C., 1985, "Full Coverage Discrete Hole Wall Cooling: Cooling Effectiveness," Int. J. Turbo Jet Engines, 2, pp. 199-212.
8. Andrews, G. E., Asere, A. A., Gupta, M. L., and Mkpadi, M. C., 1985, "Full Coverage Discrete Hole Wall Cooling: The Influence of Hole Size," Int. J. Turbo Jet Engines, 2, pp. 213-225.
9. Andrews, G. E., Alikhanizadeh, M., Asere, A. A., Hussain, C. I., Khoskbar Azari, M. S., and Mkpadi, M. C., 1986, "Small Diameter Film Cooling Holes: Wall Convective Heat Transfer," ASME J. Turbomach., 108, pp. 283-289.
10. Andrews, G. E., and Bazdidi Tehrani, F., 1989, "Small Diameter Film Cooling Holes: The Influence of The Number of Holes," ASME Paper No. 89-GT-7.
11. Andrews, G. E., Asere, A. A., Gupta, M. L., Mkpadi, M. C., and Tirmahi, A., 1990, "Full Coverage Discrete Hole Wall Cooling: The Influence of The Number of Holes and Pressure Loss," ASME Paper No. 90-GT-61.
12. Andrews, G. E., Bazdidi-Tehrani, F., Hussain, C. I., and Pearson, J. P., 1991, "Small Diameter Film Cooling Holes: The Influence of The Hole Length," ASME Paper No. 91-GT-344.
13. Harrington, M. K., McWaters, M. A., Bogard, D. G., Lemmon, C. A., and Thole, K. A., 2001, "Full-Coverage Film Cooling With Short Normal Injection Holes," ASME Paper No. 2001-GT-0130.
14. Pedersen, D. R., Eckert, E. R. G., and Goldstein, R. J., 1977, "Film Cooling With Large Density Difference Between The Main Stream and Secondary Fluid Measured By The Heat-Mass Transfer Analogy," ASME J. Heat Transfer, 99(2), pp. 620-627.
15. Ballal, D. R., and Lefebvre, A. H., 1980, "Weak Extinction Limitis of Turbulent Heterogeneous Fuel/Air Mixtures," ASME J. Eng. Power. 102(2), pp. 416-421.
16. Eckert, E. R. G., and Drake Jr., M. R., 1987, Analysis of Heat and Mass Transfer, Hemisphere, New York.
17. Lin, Y., 1997, "Study of the Inclined Multihole Film Cooling Scheme for Application to Aeroengine Combustors," Ph.D. dissertation, Beijing University of Aeronautics and Astronautics.
18. Ballal, D. R., and Lefebvre, A. H., 1973, "Film-Cooling Effectiveness in the Near Slot Region," ASME J. Heat Transfer, 95, pp. 256-266.
19. Ballal, D. R., and Lefebvre, A. H., 1972, "A Proposed Method for Calculating Film-Cooled Wall Temperatures in Gas Turbine Combustion Chambers," ASME Paper No. 72-WA/HT-24.