A generic controller for part surface temperature on a plastic injection molding machine

Advances in Polymer Technology

Volumn 25, Issue 1, 2006, Pages 1-12

  Dubay, R ^a   Pramujati, B ^b   Hernandez, M ^a  

^a UNIVERSITY OF NEW BRUNSWICK   (Canada)

^b DEPARTMENT OF ELECTRICAL ENGINEERING   (Indonesia)

Author keywords

Control; Coolant flow rate; Injection molding; Modeling; Simulations; Surface temperature

Indexed keywords

CLOSED LOOP CONTROL SYSTEMS; COMPUTER SIMULATION; COOLING; FLOW CONTROL; INJECTION MOLDING; PROCESS CONTROL; TEMPERATURE CONTROL; TWO TERM CONTROL SYSTEMS;

COOLANT FLOW RATE; MECHATRONIC CONTROL SYSTEM; SURFACE TEMPERATURE;

PLASTICS MOLDING MACHINES;

EID: 33645078105     PISSN: 07306679     EISSN: 10982329     Source Type: Journal    
DOI: 10.1002/adv.20053     Document Type: Article

References (28)

1. Rosato, D. V.; Rosato D. V.; Rosato, M. G. Injection Molding Handbook, 3rd ed.; Kluwer Academic Publishers: Dordrecht, 2000.
2. Woll, S. L. B.; Cooper, D. J. Polym Eng Sci 1997, 37, 801.
3. Kamal, M. R.; Patterson, W. I.; Gomes, V. G. Polym Eng Sci 1986, 26, 854.
4. Coughlin, J. Modern Plastics 1992, April, 101.
5. Dubay R.; Bell, A. C.; Gupta, Y. P. Polym Eng Sci 1997, 37, 1550.
6. Dubay, R. ISA Trans 2002, 41, 81.
7. Gomes, V. G.; Patterson, W. I.; Kamal, M. R. Polym Eng Sci 1986, 26, 867.
8. Golden, N. H. Proc SPE ANTEC 1975, 158.
9. Gao, F. Ph. D. Dissertation, Department of Chemical Engineering, McGill University, 1993.
10. Patterson, W. I.; Gao, F.; Kamal, M. R. Proc SPE ANTEC 1994, 701.
11. Macfarlane, S.; Dubay, R. Proc SPE ANTEC 2000, 653.
12. Dubay, R. J Injection Molding Technol 2001, 5, 72.
13. Srinivasan, K.; Srinivasan, T.; Maul, G. P. Proc SPE ANTEC 1991, 343.
14. Gao, F.; Patterson, W. I.; Kamal, M. R. Adv Polym Technol 1994, 13, 111.
15. Gao, F.; Patterson, W. I.; Kamal, M. R. Eng Plastics 1995, 8, 136.
16. Kirch, D.; Menges, G. Proc SPE ANTEC 1985, 761.
17. Catic, I. J. Polym Eng Sci 1979, 19, 893.
18. Patterson, W. I.; Kamal, M. R.; Gao, F. Proc SPE ANTEC 1990, 227.
19. Friel, P. Kunststoffee (German Plastics) 1986, 1, 3.
20. Gao, F.; Patterson, W. I.; Kamal, M. R. Intern Polym Process 1993, 8, 147.
21. Yang, S. Y.; Lien, L. Adv Polym Technol 1996, 15, 289.
22. Frutiger, R. L. Polym Eng Sci 1986, 26, 243.
23. Ljung, L. System Identification, Theory for the User; Mathworks: Natick, 1999.
24. Cohen, G. H.; Coon, G. A. Trans ASME 1953, 827.
25. Stephanopoulos, G. Chemical Process Control: An Introduction to Theory and Practice; Prentice-Hall: Englewood Cliffs, NJ, 1984.
26. Incropera, F.; DeWitt, D. Fundamentals of Heat and Mass Transfer; Wiley: New York, 1996.
27. Seborg, D. E.; Edgar, T. F.; Mellichamp, D. A. Process Dynamics and Control; Wiley: New York, 1989.
28. Dorf, R. C.; Bishop, R. H. Modern Control Systems; Prentice Hall: Englewood Cliffs, NJ, 1995.