Dynamic response of rigid rotors supported on rolling element bearings with an outer raceway defect

Proceedings of the ASME International Design Engineering Technical Conferences and Computers and Information in Engineering Conference - DETC2005

Volumn 1 B, Issue , 2005, Pages 1249-1261

  Nataraj, C ^a   Pietrusko, Robert Gerard ^a  

^a Villanova University   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

DEGREES OF FREEDOM (MECHANICS); MACHINE TOOLS; NUMERICAL METHODS; ROLLER BEARINGS; SPECTRUM ANALYSIS; STRESSES;

COMPRESSOR ROTORS; HERTZIAN CONTACT STRESSES; RACEWAY DEFECTS; SIGNAL PROCESSING TOOLS;

ROTORS;

EID: 33244490134     PISSN: None     EISSN: None     Source Type: Conference Proceeding    
DOI: 10.1115/detc2005-85646     Document Type: Conference Paper

References (29)

1. Nataraj, C., and Nelson, H. D., 1989. "Periodic oscillations in rotor dynamic systems with nonlinear supports: A general approach". Trans. ASME, Journal of Vibration, Acoustics, Stress and Reliability in Design, 111, pp. 187-193.
2. Briiel, and Kjaer, 1995. Order tracking analysis. Tech. Rep. 2.
3. Nataraj, C., 1984. "The simulation of cracked shaft dynamics". Master's thesis, Arizona State University.
4. Barkov, A., and Barkova, N., 1995. "Condition assessment and life prediction of rolling element bearings - parts i & II". Sound & Vibration.
5. Ypma, A., 2001. "Learning methods for machine vibration analysis and health monitoring". PhD thesis, Delft University of Technology.
6. Nataraj, C., 1987. "Periodic oscillations in nonlinear mechanical systems". PhD thesis, Arizona State University.
7. Nelson, H. D., and McVaugh, J. M., 1976. "The dynamics of rotor-bearing systems using finite elements". Journal of Engineering for Industry, 98(2), pp. 593-600.
8. Tiwari, M., and Gupta, K., 2000. "Dynamic response of an unbalanced rotor supported on ball bearings". Journal of Sound and Vibration, 238(5), pp. 757-779.
9. Liew, A., Feng, N., and Hahn, E. J., 2002. "Transient rotordynamic modeling ofrolling element bearing systems". Journal of Engineeringfor Gas Turbines and Power, 124, October, pp. 984-991.
10. Fleming, D. P., and Poplawski, J. V., 2002. Transient vibration prediction for rotors on ball bearings using load-dependent non-linear bearing stiffness. Tech. Rep. TM-2002-2111829, NASA.
11. Harsha, S. P., Sandeep, K., and Prakash, R., 2004. "Non-linear dynamic behaviors of rolling element bearings due to surface waviness". Journal of Sound and Vibration, 272, pp. 557-580.
12. Jang, G. H., and Jeong, S. W., 2002. "Nonlinear excitation model of ball bearing waviness in a rigid rotor supported by two or mor ball bearings considering five degrees of freedom". Journal of Tribology, 124, January, pp. 82-90.
13. McFadden, P. D., and Smith, J. D., 1984. "Model for the vibration produced by a single point defect in a rolling element bearing". Journal of Sound and Vibration, 96(1), September, pp. 69-82.
14. Tandon, N., and Choudhury, A., 1997. "An analytical model for the prediction of the vibration response of rolling element bearings due to a localized defect". Journal of Sound and Vibration, 205(3), pp. 275-292.
15. Wang, Y.-F., and Kootsookos, P. J., 1998. "Modeling of low shaft speed bearing faults for condition monitoring". Mechanical Systems and Signal Processing, 12(3), pp. 415-426.
16. Sopanen, J. T., and Mikkola, A. M., 2003. "Ball bearing vibration analysis including localized and distributed defects". In Proceedings of DETC'03, Paper No. DETC2003/VIB-48425, ASME.
17. Lee, Y.-S., and Lee, C.-W., 1999. "Modelling and vibration analysis of misaligned rotor-ball bearing systems". Journal of Sound and Vibration, 224(1), pp. 17-32.
18. Mitchell, J., 1981. Introduction to Machine Analysis And Monitoring. Pennwell Publishing, Tulsa, OK.
19. Tandon, N., 1994. "A comparison of some vibration parameters for the condition monitoring of rolling element bearings". Measurement, 12, pp. 285-289.
20. Wismer, N. J. Gearbox analysis using cepstrum analysis and comb liftering. Tech. rep., Bruel & Kjaer.
21. Dimaggio, S. J., Rubin, S., and Sako, B., 2001. "Gear fault detection in rocket engine turbo-machinery". Journal of Propulsion and Power, 17(2), March, pp. 225-231.
22. Rabiner, L., and Juang, B. H., 1993. Fundamentals of Speech Recognition. Prentice Hall, Englewood Cliffs, NJ.
23. Azovtsev, Y., Barkov, A., and Yudin, I., 1994. "Automatic diagnostic and condition prediction of rolling element bearing using enveloping methods". http://www.vibrotek.com/articles/new94vi/index.html.
24. Mathews, J., and Alfredson, R. J., 1984. "The condition monitoring of rolling element bearings using vibration analysis". ASME Journal of Vibration, Acoustics, Stress, and Reliability in Design, 106, pp. 447-453.
25. Li, J., and Kim, T., 1994. "Feedforward neural networks for fault diagnosis and severity assessment of a screw compressor". ASME Journal of Dynamic Systems and Control, 55(2), pp. 987-994.
26. Li, J., and Fan, Y., 1997. "Recurrent neural networks for fault diagnosis and severity assessment of a screw compressor". ASME Journal of Dynamic Systems and Control, 61(1), pp. 257-264.
27. Harris, T. A., 2002. Rolling Bearing Analysis, fourth ed.John Wiley & Sons, New York, NY.
28. Adams, G. P., and Qin, Z. H., 1997. "Compression load transmission in screw compressors". Journal of Sound and Vibration, 207(5), pp. 671-691.
29. Mimmi, G., and Pennacchi, P., 2001. "Compression load dynamics in a special helical blower; a modeling improvement". Journal of Mechanical Design, 123, September, pp. 402-407.