Surface visual quality of gas-assisted injection molded ABS parts with various gas channel designs

Journal of Reinforced Plastics and Composites

Volumn 23, Issue 10, 2004, Pages 1115-1129

  Chen, Shia Chung ^a   Lin, Ming Chung ^a   Chien, Rean Der ^b   Teng, Min Yu ^b   Chen, Chun Sheng ^c  

^a NANYA INSTITUTE OF TECHNOLOGY   (Taiwan)

^b CHUNG YUAN CHRISTIAN UNIVERSITY   (Taiwan)

^c LUNGHWA UNIVERSITY OF SCIENCE AND TECHNOLOGY   (Taiwan)

Author keywords

Chromatic aberration; Gas assisted injection molding; Glossy difference

Indexed keywords

COMPUTER SIMULATION; CRYSTALLIZATION; DISTORTION (WAVES); PARAMETER ESTIMATION; RESIDUAL STRESSES; TENSILE STRENGTH;

CHROMATIC ABERRATION; GAS-ASSISTED INJECTION MOLDING (GAIM); GLOSSY DIFFERENCE; SURFACE VISUAL QUALITY;

INJECTION MOLDING;

EID: 3142764540     PISSN: 07316844     EISSN: None     Source Type: Journal    
DOI: 10.1177/0731684404037041     Document Type: Article

References (22)

1. Rush, K.C. (July 1989). Plastics Eng., p. 35.
2. Shah, S. (1991). SPE Tech. Papers, 37: 1494.
3. Turng, L.S. (1992). SPE Tech. Papers, 38: 452.
4. Shah, S. and Hlavaty, D. (1991). SPE Tech. Papers, 37: 1479.
5. Chen, S.C., Hsu, K.S. and Huang. J.S. (1995). Ind. Eng. Chem. Res., 34: 416.
6. Chen, S.C., Hsu, K.S. and Huang, J.S. (1995). J. of Applied Polymer Science, 58: 793.
7. Chen, S.C., Cheng, N.T. and Hsu, K.S. (1995). Intern. J. of Mechanical Sci., 38: 335.
8. Chen, S.C. and Cheng, N.T. (1996). Intern. Commun. Heat & Mass Trans., 23: 215.
9. Chen, S.C., Dong, J.G., Jong, W.R. and Huang, J.S. (1996). SPE Tech. Papers, 43: 663.
10. Fallon, M. (June 1989). Plastics Tech., p. 70.
11. Rush, K.C. (1989). SPE Tech. Papers, 35: 1014.
12. Baxi, I.R. (1991). SPE Tech. Papers, 37: 2268.
13. Jordan, S. (November 1990). Kunststoffe Europe, p. 197.
14. Jaroschek, C. (1991). Plastics Processing, 15: 9.
15. Grelle, P.F., Kallman, M.A. and Tallmadge, B.J. (November 1994). 1st International Conference on Gas-Assisted Injection Molding Technology, Columbus, Ohio.
16. Hu, S.Y., Chien, R.D., Chen, S.C. and Kang, Y. (1997). Plastics Rubber and Composites, 26: 172.
17. Chien, R.D., Chen, S.C., Huang, J.S. and Huang, D.K. (1997). Plastics Rubber and Composites, 26: 462.
18. Chien, R.D., Chen, S.C., Kang, Y. and Yeh, H.Y. (1998). Journal of Reinforced Plastics and Composites. 17: 1213.
19. Chien, R.D., Cheng, C.K., Chen, S.C. and Yeh, H.Y. (1999). Journal of Reinforced Plastics and Composites, 18: 1322.
20. Chien, R.D., Chen, S.C., Yeh, H.Y. and Huang, D.K. (1999). Advances in Polymer Technology, 18: 303.
21. Yang, S.Y. and Ju, B.C. (1996). Master Thesis, National Taiwan University, Taiwan.
22. American Society for Testing and Materials. (1978). Annual Book of Standards ASTM D523-53T, Philadelphia, PA.