Fabrication and mechanical properties of Si3N4/carbon fiber composites with aligned microstructure produced by a seeding and extrusion method

Journal of the American Ceramic Society

Volumn 87, Issue 5, 2004, Pages 894-899

  Hyuga, Hideki ^a   Jones, Mark I ^b   Hirao, Kiyoshi ^b   Yamauchi, Yukihiko ^b  

^a Fine Ceramics Research Association   (Japan)

^b NATIONAL INSTITUTE OF ADVANCED INDUSTRIAL SCIENCE AND TECHNOLOGY AIST   (Japan)

Author keywords

[No Author keywords available]

Indexed keywords

ANISOTROPY; CARBON FIBERS; CRYSTAL MICROSTRUCTURE; EXTRUSION; FRACTURE TOUGHNESS; MECHANICAL PROPERTIES; POWDERS; SILICON NITRIDE; SINTERING; TEXTURES;

EXTRUDING DIRECTION; GRAIN ALIGNMENT; SEEDED MATERIAL; SEEDING;

CERAMIC MATRIX COMPOSITES;

EID: 3142714279     PISSN: 00027820     EISSN: None     Source Type: Journal    
DOI: 10.1111/j.1551-2916.2004.00894.x     Document Type: Article

References (19)

1. K. Kitamura, H. Takebayashi, M. Ikeda, and H. M. Percoulis, "Development of Ceramic Cam Roller Follower for Engine Application," SAE Tech. Pap. Ser., 972774 (1997).
2. K. Tanimoto, K. Kajihara, and K. Yanai, "Hybrid Ceramic Ball Bearings for Turbochargers," SAE Tech. Pap. Ser., 2000-01-1339 (2000).
3. H. Kita, H. Kawamura, Y. Unno, and S. Sekiyama, "Low Frictional Ceramic Materials," SAE Tech. Pap. Ser., 950981 (1995).
4. P. Andersson and K. Holmberg, "Limitation on the Use of Ceramics in Unlubricated Sliding Application Due to Transfer Layer Formation," Wear, 175, 1-8 (1994).
5. 4 Ceramics," Ceram. Eng. Sci. Proc., 22 [3] 197-202 (2001).
6. A. Gangopadhyay and S. Jahanmir, "Friction and Wear Characteristics of Silicon Nitride-Graphite and Alumina-Graphite Composites," Tribol. Trans., 34 [2] 257-65 (1991).
7. H. W. Liu and Q. Xue, "The Tribological Properties of TZP-Graphite Self-lubricating Ceramics," Wear, 198, 143-49 (1996).
8. A. Skopp and M. Woydt, "Ceramic-Ceramic Composite Materials with Improved Friction and Wear Properties," Tribol. Int., 25 [1] 61-70 (1992).
9. 4 Composite" (in. Jpn.), J. Ceram. Soc. Jpn., 109 [8] 699-703 (2001).
10. 4/Carbon Short Fiber Composites," J. Am. Ceram. Soc., 86 [7] 1081-87 (2003).
11. H. Hyuga, M. I. Jones, K. Hirao, and Y. Yamauchi, "Influence of Carbon Fibre Content on the Processing and Tribological Properties of Silicon Nitride/Carbon Fibre Composites," J. Eur. Ceram. Soc., 24 [5] 877-85 (2004).
12. K. Hirao M. Ohashi, M. E. Brito, and S. Kanzaki, "Processing Strategy for Producing Highly Anisotropic Silicon Nitride," J. Am. Ceram. Soc., 78 [6] 1687-90 (1995).
13. S. Kanzaki, M. E. Brito, M. C. Valecillos, K. Hirao, and M. Toriyama, "Microstructure Designing of Silicon Nitride," J. Eur. Ceram. Soc., 17 [15-16] 1841-47 (1997).
14. H. Teshima, K. Hirao, M. Toriyama, and S. Kanzaki, "Fabrication and Mechanical Properties of Silicon Nitride Ceramics with Unidirectionally Oriented Rodlike Grains" (in. Jpn.), J. Ceram. Soc. Jpn., 107 [12] 1216-20 (1999).
15. K. Hirao, H. Imamura, H. Teshima, M. E. Brito, M. Toriyama, and S. Kanzaki, "Effect of Seed Alignment on Microstructures and Mechanical Properties of Silicon Nitride Ceramics"; pp. 343-48 in Sintering Science and Technology. Edited by R. M. German, G. L. Messing, and R. G. Cornwall. Pennsylvania State University, University Park, PA, 2000.
16. 4 Single-Crystal Particles," Key. Eng. Mater., 89 [9] 63-66 (1994).
17. T. Nose and T. Fujii, "Evaluation of Fracture-Toughness for Ceramic Materials by a Single-Edge-Precracked-Beam Method," J. Am. Ceram. Soc., 71 [5] 328-33 (1988).
18. T. Suzuki and H. Umehara, "Pitch-Based Carbon Fiber Microstructure and Texture and Compatibility with Aluminum Coated Using Chemical Vapor Deposition," Carbon, 37, 47-59 (1999).
19. T. Ohji, K. Hirao, and S. Kanzaki, "Fracture-Resistance Behavior of Highly Anisotropic Silicon Nitride," J. Am. Ceram. Soc., 78 [11] 3125-28 (1995).