Superplastic failure mechanisms and ductility of AA5083

Advances in Superplasticity and Superplastic Forming

Volumn , Issue , 2004, Pages 127-138

  Kulas, Mary Anne ^a   Green, W P ^b   Pettengill, Ellen C ^b   Krajewski, Paul E ^c   Taleff, Eric M ^a,b  

^a UNIVERSITY OF TEXAS AT AUSTIN   (United States)

^b The University of Texas at Austin   (United States)

^c GENERAL MOTORS CORPORATION   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

GAS PRESSURE; GRAIN-BOUNDARY SLIDING (GBS); POPULATION DENSITIES; SOLUTE-DRAG CREEP (SDC);

CORROSION RESISTANCE; CREEP; DUCTILITY; GRAIN BOUNDARIES; INTERMETALLICS; PARTICLE SIZE ANALYSIS; PLASTIC DEFORMATION; STRAIN RATE; SUPERPLASTICITY; WELDABILITY;

ALUMINUM ALLOYS;

EID: 3042784583     PISSN: None     EISSN: None     Source Type: Conference Proceeding    
DOI: None     Document Type: Conference Paper

References (16)

1. O. D. Sherby and J. Wadsworth. Superplasticity-Recent Advances and Future Directions. Prog. Mater. Sci., 33 (1989) 169-221.
2. M.-A. Kulas, P. E. Krajewski, T. R. McNelley, and E. M. Taleff. Deformation and Failure Mechanisms in Commercial AA5083 Materials, Hot Deformation of Aluminum Alloys III. (edited by Z. Jin, A. Beaudoin, T. Bieler, and B. Radhakrishnan), pp. 499-507, TMS, Warrendale, PA, (2003).
3. E. M. Taleff, G. A. Henshall, T. G. Nieh, D. R. Lesuer, and J. Wadsworth. Warm-Temperature Tensile Ductility in Al-Mg Alloys. Metall. Mater. Trans., 29A (1998) 1081-1091.
4. E. M. Taleff and P. J. Nevland. The High-Temperature Deformation and Tensile Ductility of Al Alloys. JOM, 51 (1999) 34-36.
5. E. M. Taleff, P. J. Nevland, and P. E. Krajewski. Tensile Ductility of Several Commercial Aluminum Alloys at Elevated Temperatures. Metall. Mater. Trans., 32A (2001) 1119-1130.
6. J. S. Vetrano, C. A. Lavender, C. H. Hamilton, M. T. Smith, and S. M. Bruemmer. Superplastic Behavior in a Commercial 5083 Aluminum Alloy. Scripta Metall., 30 (1994) 565-570.
7. D. H. Bae and A. K. Ghosh. Cavity Formation and Early Growth in a Superplastic Al-Mg Alloy. Acta Mater., 50 (2002) 511-523.
8. D. H. Bae and A. K. Ghosh. Cavity Growth during Superplastic Flow in an Al-Mg Alloy: I. Experimental Study. Acta Mater., 50 (2002) 993-1009.
9. D. H. Bae and A. K. Ghosh. Cavity Growth during Superplastic Flow in an Al-Mg Alloy: II. An Improved Plasticity Based Model. Acta Mater., 50 (2002) 1011-1029.
10. ASTM, Standard Test Methods for Determining Average Grain Size. Standard Designation E 112-96, ASTM, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959, July 1996.
11. O. D. Sherby and P. M. Burke. Mechanical Behavior of Crystalline Solids at Elevated Temperature. Prog. Mater. Sci., 13 (1968) 325-390.
12. E. M. Taleff, T. Leon-Salarnanca, R. A. Ketcham, R. Reyes, and W. D. Carlson. Nondestructive Evaluation of Cavitation in an Al-Mg Material Deformed under Creep Conditions. J. Mater. Res., 15 (2000) 76-84.
13. M. A. Burke and W. D. Nix. Plastic Instabilities in Tension Creep. Acta Metall., 23 (1975) 793-798.
14. J. W. Hutchinson and H. Obrecht. Tensile Instabilities in Strain-Rate Dependent Materials. Fracture 1977, 1 (1977) 101-116.
15. A. K. Ghosh. The Influence of Strain Hardening and Strain-Rate Sensitivity on Sheet Metal Forming. Journal of Engng. Mater. and Tech., 99 (1977) 264-274.
16. A. K. Ghosh. Tensile Instability and Necking in Materials with Strain Hardening and Strain-Rate Hardening. Acta Metall., 25 (1977) 1413-1424.