Ejection force in tubular injection moldings. Part I: Effect of processing conditions

Polymer Engineering and Science

Volumn 44, Issue 5, 2004, Pages 891-897

  Pontes, A J ^a   Pouzada, A S ^a  

^a UNIVERSITY OF MINHO   (Portugal)

Author keywords

[No Author keywords available]

Indexed keywords

COOLING; INTERFACES (MATERIALS); OPTIMIZATION; RESIDUAL STRESSES; SHRINKAGE; STRUCTURAL DESIGN; THERMOPLASTICS;

CATASTROPHIC EFFECTS; EJECTION FORCE; THERMAL REGULATORS;

INJECTION MOLDING;

EID: 3042670666     PISSN: 00323888     EISSN: None     Source Type: Journal    
DOI: 10.1002/pen.20080     Document Type: Article

References (19)

1. G. Menges and P. Mohren, How To Make Injection Molds, Hanser, New York (1986).
2. R. G. W. Pye, Injection Mould Design, 4th Ed., Harlow, Longman Scientific & Technical (1989).
3. Z. Wang, K. S. Lee, J. Y. H. Fuh, Z. Li, Y. F. Zhang, A. Y. C. Nee, and D. C. H. Yang, Int. J. Mater. & Product Technol., 11, 371 (1996).
4. H. Wang, K. K. Kabanemi, and G. Salloum, SPE ANTEC Tech. Papers, 43 (1997).
5. H. Wang, K. K. Kabanemi, and G. Salloum, Polym. Eng. Sci., 40, 826 (2000).
6. L. C. E. Struik, Polym. Eng. Sci., 18, 799 (1978).
7. A. I. Isayev, Injection and Compression Molding Fundamentals, Marcel Dekker, New York (1987).
8. A. Kaminski, Kunststoffe, 66, 208 (1976).
9. A. Kaminski, "Demoulding," in Injection Moulding Technology, D. Rheinfeld, ed., VDI-Verlag, Düsseldorf, Germany (1981).
10. C. Burke and R Malloy, SPE ANTEC Tech. Papers, 37 (1991).
11. R. Balsamo, D. Hayward, and R. Malloy, SPE ANTEC Tech. Papers, 39 (1993).
12. H. Wang, R. Connolly, and G. Salloum, Proceedings of Mechanics in Design, CSME Forum (1996).
13. K. Shen, L. Chen, and L. Jiang, Plastics, Rubber and Composites, 28, 341 (1999).
14. T. Sasaki, N. Koga, K. Shirai, Y. Kobayashi, and A. Toyoshima, J. Precision Engineering, 24, 270 (2000).
15. A. J. Pontes, A. M. Pinho, A. S. Miranda, and A. S. Pouzada, O Molde, 34, 25 (1997).
16. A. J. Pontes, Shrinkage and Ejection forces in Injection Moulded Products, PhD thesis, Universidade do Minho, Guimarães (2002).
17. A. J. Pontes, A. M. Brito, and A. S. Pouzada, J. Injection Molding Technology, 6, 343 (2002).
18. A. J. Pontes, R. Pantani, G. Titomanlio, and A. S. Pouzada, SPE ANTEC Tech. Papers, 60 (2002).
19. G. Menges and H. Bangert, Kunststoffe, 71, 13 (1981).