Gas turbine fogging technology: A state-of-the-art review part II: Overspray fogging - analytical and experimental aspects

Proceedings of the ASME Turbo Expo

Volumn 4, Issue , 2005, Pages 83-90

  Bhargava, R K ^a   Meher Homji, C B ^b   Chaker, M A ^c   Bianchi, M ^d   Melino, F ^d   Peretto, A ^d   Ingistov, S ^e  

^a JACOBS ENGINEERING   (United States)

^b Bechtet Corporation   (United States)

^c Gas Turbine Division   (United States)

^d UNIVERSITY OF BOLOGNA   (Italy)

^e BP ^*  (United States)

Author keywords

High fogging; Overspray; Power augmentation; Wet compression

Indexed keywords

HIGH FOGGING; OVERSPRAY; POWER AUGMENTATION; WET COMPRESSION;

COOLING; EVAPORATION; HEATING; INTAKE SYSTEMS;

GAS TURBINES;

EID: 27744577620     PISSN: None     EISSN: None     Source Type: Conference Proceeding    
DOI: 10.1115/GT2005-68337     Document Type: Conference Paper

References (24)

1. Bhargava, R. K., Meher-Homji, C. B., Chaker, M. A., Peretto, A., Bianchi, M., Melino, F., and Ingistov, S., 2005, "Gas Turbine Fogging Technology- A State-of-the-Art Review, Part I: Inlet Evaporative Fogging- Analytical and Experimental Aspects," ASME Paper No. GT2005-68336.
2. Bhargava, R. K., Meher-Homji, C. B., Chaker, M. A., Peretto, A., Bianchi, M., Melino, F., and Ingistov, S., 2005, "Gas Turbine Fogging Technology- A State-of-the-Art Review, Part III: Practical Considerations and Operational Experience," ASME Paper No. GT2005-69144.
3. Kleinschmidt, R. V., 1947, "Value of Wet Compression in Gas-Turbine Cycles," Mechanical Engineering, Am. Soc. Mech. Eng., 69 [2], pp. 115-116.
4. Wilcox, E. C. and Trout, A. M., 1951, "Analysis of Thrust Augmentation of Turbojet Engines by Water Injection at Compressor Inlet Including Charts for Calculating Compression Processes with Water Injection," NACA Report No. 1006.
5. Beede, W. L., Hamrick, J. T., and Withee, J. R., 1951, "Evaluation of Centrifugal Compressor Performance with Water Injection," NACA RM-E51E21.
6. Hill, P. G., 1963, "Aerodynamic and Thermodynamic Effects of Coolant Injection on Axial Compressors," Aeronautical Quarterly, pp. 331-348.
7. Zheng, Q., Sun, Y., Li, S., and Wang, Y., 2002, "Thermodynamic Analyses on Wet Compression Process in the Compressor of Gas Turbine, ASME Paper No. GT-2002-30590.
8. Utamura, M., Kuwahara, T., Murata, H., and Horii, N., 1999, "Effects of Intensive Evaporative Cooling on Performance Characteristics of Land-Based Gas Turbine," Joint Power Generation Conference, PWR-Vol. 34.
9. Horlock, J. H., 2003, "Compressor Performance with Water Injection," ASME Paper No. 2001-GT-0343.
10. Haertel, C. and Pfeiffer, P., 2003, "Model Analysis of High-Fogging effects on the work of Compression," ASME Paper No. GT2003-38117.
11. White, A. J. and Meacock, A. J., 2003, "An Evaluation of the Effects of Water Injection on Compressor Performance," ASME Paper No. GT2003-38237.
12. Sexton, W. R. and Sexton, M. R., 2003, "The effects of Wet Compression on Gas Turbine Engine Operating Performance," ASME Paper No. GT2003-38045.
13. Zheng, Q., Li, M., and Sun, Y., 2003, "Thermodynamic Performance of Wet Compression and Regenerative (WCR) Gas Turbine," ASME Paper No. GT2003-38517.
14. Van, J., Ji, X. and Jonsson M., 2003, "Thermodynamic Property Models for the Simulation of Advanced Wet Cycles," ASME Paper No. GT2003-38298.
15. Jolly, S., 2003, "Performance Enhancement of GT 24 With Wet Compression," Power-Gen International, Dec. 9-11, Las Vegas, NV, USA
16. Utamura, M., Takehara, I., Horii, N., and Kuwahara, T., 1997, "A New Gas Turbine Cycle for Economical Power Boosting," ASME Paper No. 97-AA-142.
17. Li, M. and Zheng, Q., 2004, "Wet Compression System Stability Analysis: Part I - Wet Compression Moore Greitzer Transient Model," ASME Paper No. GT2004-54018;
18. and Part II - "Simulations and Bifurcation Analysis," ASME Paper No. GT2004-54020.
19. Arsen'ev, L. V. and Berkovich, A. L., 1996, "The Parameters of Gas-Turbine Units with Water Injected into the Compressor," Thermal Engineering, 43 [6], pp. 461-465.
20. Ingistov, S., 2001, "Interstage Injection System for Heavy Duty Industrial Gas Turbine Model 7EA," ASME Paper No. 2001-GT-407.
21. Bagnoli, M., Bianchi, M., Melino, F., Peretto, A., Spina, P. R., Bhargava, R., and Ingistov, S., "A Parametric Study of Interstage Injection on GE Frame 7EA Gas Turbine," ASME Paper No. GT2004-53042.
22. van Liere, J. and Laagland G. H. M., 1998, "The TOPHAT Project - Swirl Flash Technology to Reduce Maintenance Costs," KEMA Report No. 00376-KPG/SUP 98-1382.
23. van Liere, J, Meijer C.G., "Power Augmentation and Nox Reduction of Gas Turbines by SwirlFlash Overspray Injection", Alpha Power Systems Publication.
24. van Liere, J. and Laagland G. H. M., and Meijer, C. G. "Retrofit of Gas Turbines by SwirlFlash Overspray," Alpha Power Systems Publication.