Design and optimisation of punching/blanking systems aided by experimental modelling

International Journal of Vehicle Design

Volumn 39, Issue 1-2, 2005, Pages 125-139

  Klingenberg, W ^a   Singh, U P ^b  

^a UNIVERSITY OF GRONINGEN   (Netherlands)

^b UNIVERSITY OF ULSTER   (United Kingdom)

Author keywords

Experimental modelling; In process control; Punching blanking

Indexed keywords

COST EFFECTIVENESS; DESIGN; HYDROSTATIC PRESSURE; MICROCRACKING; OPTIMIZATION; QUALITY ASSURANCE; STRESSES;

EXPERIMENTAL MODELING; IN-PROCESS CONTROL; PUNCHING/BLANKING;

PUNCHING;

EID: 25844444243     PISSN: 01433369     EISSN: None     Source Type: Journal    
DOI: 10.1504/IJVD.2005.007224     Document Type: Article

References (22)

1. Bridgman, P.W. (1952) Studies in Large Plastic Flow and Fracture, McGraw-Hill.
2. Choy, C.M. and Balendra, R. (1996) 'Experimental analysis of parameters influencing sheared-edge profiles', Proceedings 4th Int. Conf. on Sheet Metal, University of Twente, The Netherlands, Vol. II, pp.101-110.
3. Ghosh, A., Raghu Ram, V. and Popat, P.B. (1985) 'A new approach to the mechanics of the blanking operation: theoretical model and experimental verification', Journal of Mechanical Working Technology, Vol. 11, pp.215-228.
4. Gray, T.G.F. (1988) Tensile Testing, Mechanical Testing, Curbishley, I. (Ed.), The Institute of Metals, London.
5. Hambli, R. (2001) 'Blanking tool wear modelling using the finite element method', International Journal of Machine Tools & Manufacture, Vol. 41, No. 12, pp.1815-1829.
6. Hambli, R. (2002) 'Design of experiment based analysis for sheet metal blanking process optimization', International Journal of Advanced Manufacturing Technology, Vol. 19, pp.403-410.
7. Hambli, R. and Potiron, A. (2000) 'Finite element modelling of sheet-metal blanking operations with experimental verification', Journal of Materials Processing Technology, Vol. 102, Nos. pp. 1-3, 257-265.
8. Klingenberg, W. (2000) Numerical Modelling of the Punching/Blanking Process Using In-Process Characterisation of Steel, PhD Dissertation, University of Ulster.
9. Klingenberg, W. and Singh, U.P. (2003) 'Finite element simulation of the punching/blanking process using in-process characterisation of mild steel', Journal of Materials Processing Technology, Vol. 134, No. 3, pp.296-302.
10. Klingenberg, W., Singh, U.P. and Urquhart, W. (2002) 'Numerical simulation of the punching/blanking process', Proceedings 7th International Conference on Technology of Plasticity, Yokohama, Japan, pp.907-914.
11. Klocke, F. and Sweeney, K. (1998) 'Crack prediction and prevention in the fine blanking process: FEM simulations and experimental results', Proceedings International Conference on Sheet Metal, University of Twente, The Netherlands, April, pp.215-222.
12. Krämer, W. (1968) 'Contribution to the determination of force and deformation work in sheet blanking (in German)', Ind-Anz., Vol. 90, pp.361-365.
13. Lange, K. (1985) Handbook of Metal Forming, McGraw-Hill, New York, Chapter 24.
14. Ramaekers, J.A.H. (1970) Härte und Verformung Metallischer Werkstoffe, PhD Dissertation, University of Eindhoven, The Netherlands.
15. Ramaekers, J.A.H. and Kals, J.A.G. (1986) 'Strain, stresses and forces in blanking', Proceedings 8th IMC Conference, University College Galway, Ireland, pp. 126-138.
16. Schey, J.A. (1987) Introduction to Manufacturing Processes, 2nd int. ed., McGraw-Hill.
17. Singh, U.P. (1977) 'Numerical analysis of the distortional behaviour of a hydraulic press', Annals of CIRP, Vol. 16, No. 1, pp. 119-226.
18. Singh, U.P., Kals, H.J.J. and Streppel, A.H. (1990) 'Computer aided design study of a die-set for punching/blanking', Proceedings of the 28th Int. MTDR Conf., Vol. 28, pp.379-386.
19. Singh, U.P., Klingenberg, W. and Urquhart, W. (1993) 'Selection of press tools for punching operations', Proceedings 26th ISATA Conference, Aachen, Germany, pp.425-433.
20. Singh, U.P., Klingenberg, W. and Urquhart, W. (1994) 'Effect of tool geometry on punching performance', Journal of Engineering for Industry - Transactions ASME, November, Vol. pp.116, pp.508-513.
21. Singh, U.P., Wilson, R. and Hinduja, S. (1985) 'Computer aided study of a single column hydraulic press', Proceedings of the 25th Int. MTDR Conference, Vol. 25, pp.389-395.
22. Taupin, E., Breitling, J., Wu, W-T. and Altan, T. (1996) 'Material fracture and burr formation in blanking results of FEM simulations and comparison with experiments', Journal of Materials Processing Technology, Vol. 59, pp.68-78.